Question about 2007 Kia Sedona LX Minivan

Open Question

I have a 2008 Sedona GS. 1. How do I get the sensor wiring from the bumper into the rear of the car.(which side is best) 2. Where is the best place to mount the sensor box. 3. Best way to take a live feed from the reversing light.

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 48 Answers

SOURCE: Auto wiring

you should use a relay so that the fridge is only powered when your kia engine is running. reason being to stop the towing vehicle going flat if connected direct onto the other battery when parked for a long time.if this wont be a problem as in you have a hook up when parked and not using the towing vehicle just connect the wire direct onto the battery thru a fuse.hope this helps

Posted on Apr 12, 2009

Ad
  • 77 Answers

SOURCE: how to remove the rear bumper on a 2005 Kia Sedona

1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Posted on Jan 30, 2010

  • 179 Answers

SOURCE: where is the starter on a 2008 kia sedona?

petrol or diesel

Posted on Feb 23, 2010

360dreamworx
  • 314 Answers

SOURCE: Where is o2 sensor bank

I hope the pic helps. B1/B2 Bank 1 Sensor 2 #3 in pic.


360dreamworx_6.jpg

Posted on Jul 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace rear parking sensor


You have to take bumper cover off .
Remove rear bumper fascia. Refer to Rear Bumper Fascia Replacement . Disconnect electrical from the rear object sensor. Lift the locking tabs on the housing and remove the rear object sensor.
Preliminary Procedure
  1. Remove the compartment sill plate. Refer to Rear Compartment Sill Trim Plate Replacement .
  2. Remove rear wheel liners. Refer to Rear Wheelhouse Panel Liner Replacement .
1
Rear Fascia Push Pin Retainers (Qty: 2)
2
Rear Fascia Nuts (Qty: 4)
Tighten
10 N?·m (89 lb in)
3
Rear Fascia Bolts (Qty: 2)
4
Rear Fascia Bolts (Qty: 6)
5
Rear Fascia
Tip
?€¢
Energy absorber and fascia are removed together. Cannot be separate on vehicle.


?€¢
Disconnect the electrical connectors.

Dec 22, 2015 | 2006 Cadillac DTS

Tip

Add on the Park Distance Control


Spent last weekend installing one, I can comment on installation. First, the car is not at all "pre-wired" for the PDC. The installation involves the following: 1. Removing the rear bumper completely (not just the black rub strip) 2. Running a wiring harness thru the bumper. 3. Removing and replacing the rub strip with one designed to accomodate the ultrasonic sensors. 4. Drilling a 40 mm (about 1 1/2 in.) diameter hole below the right rear tail light to pass the wiring harness thru (a very scarey operation, for me, at least. Like performing surgery on your baby!). 5. Removing the rear package shelf (which means removing the rear seats, head restraints, C pillar panels, child seat tethers, etc.) 6. Installing a small speaker next to the brake light on the rear panel. 7. Running a second wiring harness from the trunk into the passenger compartment and along the rear window to connect to the speaker. 8. Tapping into the fuse block above the battery. 9. Running the power harness across the back of the trunk to the left side of the car to tap into the I-bus wiring. 10. Mounting the PDC control unit above the battery. 11. Re-assembling everything. Given the somewhat cryptic instructions, and the fact that the actual wiring did not match what was described in the instructions, it is a pretty time-consuming project. Concerning whether it is any different from the factory installed version: I haven't seen the factory installed one, but my guess is that they are pretty much the same.

on May 19, 2008 | 1988 BMW M5

1 Answer

Why are my backup sensors not coming on


if you have something in trailer hitch blocking bumper rear bumper dirty ,damaged rear bumper by sensor[s] or damaged /malfunction of sensor check the wiring and connections behind bumper those circular inserts are the rear sensors

Nov 16, 2015 | 2008 GMC Envoy

2 Answers

2008 ford escape. removal of rear bumper cover


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Good Luck

Feb 27, 2015 | 2008 Ford Escape

1 Answer

Location of bank 2 sensor 1 on a kia Sedona 2005 lx


left side of exaust after catalictic converter

Oct 27, 2014 | 2005 Kia Sedona

1 Answer

How to remove bumper


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly.

2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle.
3. Install rear bumper in reverse order of removal.

Dec 22, 2013 | 2004 Kia Sedona

1 Answer

How do I remove the panel that hold the rear parking sensors on a 2001 S550?


There are six bolts from the bumper into the rear cross member to remove, accessible from inside the boot. You'll have to remove the rubber plugs to get to two of them. After that, remove the boot lining (that's the "trunk" lining if you're a Yank) and you'll see four bolts (two on each side) that secure the bumper by screwing downwards through the metal wing into the top sides of the bumper. Now go underneath the car, and there are two bolts accessible at the rear of the bumper, accessible from beneath. Now you need to uncrew a pair of 10mm plastic nuts under the wheel arch lining/mudflap and two which are behine the rear wheels. Fold the wheel arch lining away from the bumper and there's a screw in the very front of the sides of the wing right at the point where it connects to the wheel arch. remove these (one on each side) and the bumper will slide backwards and off the body. Voila. Piece of cake. Remember to disconnect the wiring to the rear sensors and pull the multiplug through out of the hole, carefully removing the grommet.

Re-fitting is a bit trickier, so use a couple of beer crates or boxes to hold the bumper up below the rear as you line up the tabs on the air exits and slide the bumper back.

Dec 23, 2011 | 2001 Mercedes-Benz S-Class

2 Answers

I have a 2006 Ford Explorer and 2 of my park aid assist sensor are bad. They are in the rear bumper. How would i replace the sensors? Is it really necessary to remove the bumper?


You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Apr 01, 2010 | 2006 Ford Explorer

1 Answer

How to remove the rear bumper on a 2005 Kia Sedona


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Nov 09, 2009 | 2005 Kia Sedona

1 Answer

I want to fit a towbar to my ford focus hatch 2008 model. What is involved in removing rear bumper Regards Brian Lamb


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Oct 27, 2009 | 2007 Ford Focus (3 Door) Hatchback

Not finding what you are looking for?
2007 Kia Sedona LX Minivan Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...