Question about 2003 Ford Focus

1 Answer

Is it hard to fit Ford focus 1.8 tdi 03 plate?

How to fit a new clutch?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,340 Answers

Well, not necessarily hard, but pretty complicated. Trans has to come out, and it is harder than in the olden days.... Be sure to also resurface the flywheel, replace all seals that you encounter, replace the release bearing and pilot bearing.

Remember to align the clutch plate with a dummy imput shart....

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is an oily substance running down the mat and carpet behind the clutch pedal on my for d focus


Depending on what you focus has there will be two reservoirs under the bonnet if the clutch is hydraulic there will be one for the clutch but there is a seperate one for the brakes check these reservoirs to see how full they are if either of these leak from the pistons inside the fluid will run past the seals and eventually in to the vehicle if your clutch is hydraulic the telltale sign will be if you look up behind the dash board where the pedals are one of the areas where the pedals are or even the top of the pedal itself will be wet with the fluid leaking back in best to change the master cylinder as there cheap enough then when new one is fitted bleed clutch this can be achieved by filling the reservoir then follow the pipe from that reservoir down to the gearbox there will be another cylinder on the gearbox where this pipe is joined look for a bleed screw on that cylinder

Dec 27, 2014 | Ford Focus Cars & Trucks

1 Answer

Ford focus 1800,tdi 2006 year.1000110 on the clock vibration on gear stick drives ok is it due a new clutch and how many parts is it 4parts required


3 new parts usaly, Clutch, Pressure plate, And throw out bearing, Sometimes a throw out bearing requires the slave cylender if so equipped

Jun 06, 2010 | 2005 Ford Focus

1 Answer

Just had new clutch fitted on 02 ford focus 1.6 now making noise but stops when i press clutch down


A couple of things comes to mind, when you press the clutch you disengage the transmission. When the clutch is not pressed the transmission still spins inside even when it is in neutral. Sounds like a bearing inside the transmission is making noise, did they put fluid back in the transmission? Also another common source of noise is the throw out bearing, it is on the input shaft, it is the actual part that presses against the clutch pressure plate, usually though they make noise when the clutch is pressed and quiet down when released.

May 07, 2010 | 2004 Ford Focus

1 Answer

1993 model ford lazer 5 speed manaul,clutch is not engaging properly, hard to select a gear, travels ok when in gear, happened in one day??


Just rip the clutch out and fit a new clutch ,its not clearing properly ,so its either the hydraulics if fitted but i would go for the pressure plate spring ,but without having it in front of me its difficult to diagnose ,

Dec 22, 2009 | Ford Laser Cars & Trucks

2 Answers

How to fit clutch in ford focus 1.8 1999


need clutch aliment tool any part store has them

Nov 27, 2009 | 2000 Ford Focus

2 Answers

Fitting an isofix car seat in a ford cmax 57 plate tdi


if there are a small part of the backseat (ca 10 cm high located at the bottom of the back) that can be picked out, you have isofix points.
if your backseats are in one pice, theres not

Apr 11, 2009 | 2007 Ford Focus (3 Door) Hatchback

2 Answers

Air bag light keeps coming on in ford focus 03 plate zetec 1.6 wa


Common fault on FORD
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.


Just push it together properly and it should clear the AirBag fault


Apr 08, 2009 | 2003 Ford Focus

1 Answer

How easy is it to replace a noisy clutch thrust bearing. 53 plate Ford Focus 1.6 petrol zetec.


The thrust bearing is normally a part of a new clutch kit.Comprises pressure plate, clutch plate and thrust bearing.You will need to remove the gear box to change the bearing.The bearing basically slides onto the gearbox shaft. Recommend changing all three rather than just the beaing.You may want to get quotes from garages as dealers are expensive.

Mar 08, 2009 | 2003 Ford Focus

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...