Question about 1989 Ford Mustang

1 Answer

Freeze plugs how many freeze plugs are on ''89 5.0 motor? How do you replace the rear ones?

Posted by on

  • Anonymous Mar 24, 2014

    I'VE HAD 1 REPLACE,HOWEVER MY MECH. SAY THEY'LL ALL GO SOONER THAN LATER ANS I KNOW THE REAR ONE INVOLVES DROPPING THE TRANSMISSION??/
    WILL THERE BE ANY OTHER PROBS I NEED TO LOOK OUT FOR?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 921 Answers

More than two that i've seen real quick...to get them out you drill a hole into the center of the pludg and pry them out..just do whatever it take....you be installing new ones anyway.

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the freeze plug that's under the motor mount 09 1994 F250 7.5


Well, I own a 7.5 powered F-250 but I can't remember that particular freeze plug. When you can't pull the motor, you can at least take the rear tranny mount loose and loosen the engine mounts,put a flat board under it so no dents fron the jack you'll be using. You might even have to loosen exhaust bolts,I dunno, and get some space.
THEN what I have done is pry out the bad freeze plug(punch a hole in the center if you can) and then go to NAPA and get an aftermarket bolt-in type plug. I use the rubber EXPANSION type,but I think they make brass ones too.
Check them out! don-ohio

Mar 02, 2017 | Ford F-250 Cars & Trucks

1 Answer

Do I need to pull the transmission to replace freeze plugs in the 1989 crown Victoria?


depends which freeze plugs your changing. if its the ones at the rear of the heads or back of motor being covered by the bell housing then yes it has to be pulled.

Apr 25, 2015 | 1989 Ford Crown Victoria

1 Answer

Replace rear freeze plug 1998 Z71


depends on your working conditions but it is usually easy to replace all the freeze plugs with the motor out which is what i would do it they r starting to rust through, but it is also easier to realign the trans to the motor than a motor to a trans so really depends on if u r doing more than one freeze plug.

Feb 06, 2013 | Cars & Trucks

1 Answer

I have cooler leak,Between Motor and transmission i think has block engine metallic seal damage.


Your problem is the freeze plug located between the rear of the motor and the flywheel and you need to remove the transmission to replace the freeze plug to fix your problem. Good Luck ! Michael...

Oct 11, 2011 | 1998 Honda Passport

1 Answer

I need to know where the freezeout plugs are located and how many of them are there?


The freeze, core or expension plugs are located on both sides and front and read of the block. Depending on what you're working with determin how many. For instance, my 89 350 will have two on each side of the engine block, two on the rear behind the flexplate (one on each bank) and two on the front (one on each bank).

Aug 24, 2011 | Chevrolet C1500 Cars & Trucks

2 Answers

Replacing freeze plugs withyout taking flywheel off and ......


HI,Yes you have a total of 8 freeze plugs on this engine,2 at the rear of the engine behind the flywheel/flexplate,2 on the front of the engine and 2 on each side of the block.1 on each side hides behind the motor mounts.Hope this helps.Thank You for using fixya. please rate this if it helps.Thank You,iluv2fish.... Ray....

Jul 06, 2010 | 1983 Chevrolet Blazer

1 Answer

Freeze plugs on 1999 dodge durango how do I replace the rear freeze plug


If you speak of the freeze plugs on the rear of the block, the transmission must come out to make the repair.

If if the plug is on the side of the block, most likely the plug can be replaced will out too much fanfare.

This was a known issue on the 5.2/5.9 motors. Best to replace all of them if you have to remove the trans.

Jun 09, 2010 | 1999 Dodge Durango

1 Answer

To replace the rear freeze plugs, am i gonna have to pull the whole engine out?


Unfortunately that would be the best way to do it. It 's very difficult to get to them with the motor in the car. If you can knock out the old ones, you might have luck using the expandable rubber freeze plugs, instead of having to try to pound in steel ones.

May 07, 2010 | 1997 Dodge Avenger

3 Answers

1991 (4 cylinder) Toyota Camry freeze plug problem


the price is determined by how much you have to remove in order to gain access to the freeze plug to replace it the freeze plugs themselves are just a couple of dollars but could be several hundred to replace due to gaining access to replace you also have freeze plugs sometimes that are on back of engine and require you to either remove engine or transmission to replace also keep in mind that normally if a freeze plug is leaking it is due to a neglected cooling system that is now full of rust that may have to be flushed out

May 03, 2010 | 1991 Toyota Camry

2 Answers

Freeze Plug


Major job without the right tools! There are freeze plugs hidden by the bell housing on the trans. If you can see the plug without pulling the trans, use a long punch and knock the plug out(poke a hole in one edge and pry out).If you can't see the plug pull the trans. replace the plug. (you need an engine holder to hold the engine in place from the top.

May 22, 2009 | 2001 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...