Question about 1989 GMC Sierra

1 Answer

We have bled the lines on a 1994 gmc sierra and are getting no tension in the clutch what do we do?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 832 Answers

From your comments, your clutch master is no longer
working. Check your clutch master, and replace all the
worn out parts. You can buy all of these in one pack,
specify Clutch Master Repair Kit for 1989 GMC Sierra.

Posted on Oct 05, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1985 GMC Sierra clutch

It takes a lot of bleeding, keep bleeding it off, make sure your hose clamps or nuts are tight, sometimes there's an o-ring where the hose is, check to see if yours has one, but you have to bleed the system thoroughly

May 01, 2017 | GMC K2500 Cars & Trucks

1 Answer

1994 gmc sierra ac clutch engages and disengages rapidly

it will short cycle while refrigerant is being added slows down when level starts to reach normal

Nov 06, 2017 | 1994 GMC Sierra

1 Answer

"How to remove and replace a AC Clutch on a 1994 GMC Sierra 5.7?"

depending on witch compressor you have they all are very straight forward , just remove the screws that hold the out side plate to the electric clutch and find the screw that holds everything together in the center ,remove it and it should slide out with no problem. get a replacement and install it the reversed way

Aug 05, 2010 | 1994 GMC Sierra

1 Answer

Is it fairly easy to install a clutch master cylinder (1994 gmc sierra 2500)my main concern is disconnecting and reconnecting the push rod to the clutch pedal through the little hole in the fire wall is is...

it is very easy to replace the parts, bleeding the air is the real problem, u will need to buy a Mityvac brand vacuum clutch bleeding tool, with out it you will never get the air out of the system after the parts are replaced, also always replace the clutch master and the clutch slave at the same time.

Jan 11, 2010 | 1994 GMC Sierra

1 Answer

1997 GMC Sierra 5.7 changed master cylinder calipers and brake pads. I have a hard pedal until I turn the truck on and the pedal goes to the floor? Is there something I am missing? I have bled the brakes...

check under your master cylinder,is there another clyinder below with one line in and one line out,if you do I found this is for the Abs to the rear,I had to replace this it was full of air,and did exactly what yours is now

Dec 06, 2009 | 2003 GMC Sierra 1500

1 Answer

1994 gmc sierra truck, have no clutch pedal at all, goes right to floor without pressure

Probably blew the rubber diaphram in the clutch master cylinder. Rebuild kits are fairly cheap and easy.

Jul 07, 2009 | 1994 GMC Sierra

1 Answer

Clutch wont engage

With the hydraulic systems, there is no adjustment. So what pedal travel you have is likely normal for that vehicle.

May 30, 2009 | 1994 GMC Sierra

1 Answer

1995 gmc sierra clutch pressure problem

could be wrong here but sure sounds like its out of fluid at the "master cylinder" look near the brake master cylinder for a seperate little container for the clutch. bleeding is tricky because it is small and wants to run out of fluid quick. you have to keep adding each time you bleed. Hope I helped. Thanks

Feb 26, 2009 | 1995 GMC Sierra C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides