Question about 2002 Volkswagen Passat

1 Answer

Front suspension in 99 passat is squeeky. new shocks did'nt help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

Torsion bars are worn spray with WD forty on all the rubber grommets and that should quite them up for a few months.

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

99 expedition two wheel drive passenger side goes up higher than the drivers side.uneven ride! whats a ride height sensor?


height sensor is a sensor that control air compressor on air shock.it keep vechicle level.if height sensor senses distance between frame and suspension .it will admit air to shock by controling the air compressor.check the air shock on driver side.BESURE TO TURN OFF ELECTRICAL POWER TO AIR SUSPENSION BEFORE RAISING VECHICLE.

Jul 10, 2009 | 2000 Ford Expedition

1 Answer

Replacing front struts


Okay....here is the steps first....and then the directions on how to use the tools:

  1. Raise and properly support the vehicle.
  2. Remove the front wheel.
  3. Detach the shock absorber lower mount by removing the two bolts.
  4. Remove the retainer nut, retainer, cushion and shock absorber.
  5. Detach the cushion retainer from the shock absorber.
  6. Compress the coil spring with a commercially available spring compressor.
  7. Detach the stabilizer bar.
  8. Support the upper suspension arm and steering knuckle securely.
  9. Remove the cotter pin.
  10. Loosen and remove the nut.
  11. Using a ball joint removal tool, detach the lower ball joint from the lower control arm.
  12. Loosen the suspension arm set bolt.
  13. Remove the suspension arm set bolt nut.
  14. Remove the nut from the strut bar front set bolt.
  15. Pull out both set bolts.
  16. Remove the lower suspension arm and coil spring. To install:
  17. Installation is the reverse of removal. Note the following torque specifications:
    1. Strut bar front set bolt: 221 ft. lbs. (300 Nm)
    2. Lower suspension arm set bolt: 148 ft. lbs. (200 Nm)
    3. Lower ball joint nut: 80 ft. lbs. (110 Nm)
    4. Lug nuts: 83 ft. lbs. (110 Nm).

May 13, 2009 | 1998 Toyota Tacoma

1 Answer

Front Sway bar(Stabilizer bar)


please give good rating if this helps


Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Remove and discard nuts retaining stabilizer bar link (5K484) assembly to front stabilizer bar (5482) and front shock absorber (18124) with an 8 mm closed-end wrench and an 18 mm open-end wrench.


    ccf2026.gif

  1. Remove nuts retaining steering gear (3504) to front sub-frame, and move steering gear off the front sub-frame.
  1. With another set of support safety stands under front sub-frame, remove two rear subframe retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).




  1. Remove front stabilizer bar U-bracket bolts and replacestabilizer bar brackets and/or front stabilizer bar as required. Discard lower suspension arm stabilizer bar insulator (5493) and bolts.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar insulator installation position.
  1. Lubricate inside diameter of new lower suspension arm stabilizer bar insulator with Rubber Suspension Insulator Lube E25Y-19553-A or equivalent meeting Ford specification ESF-M99B112-A. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber lower suspension arm stabilizer bar insulators.
  1. Install new lower suspension arm stabilizer bar insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on front sub-frames and install new bolts. Tighten to 30-40 Nm (22-29 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Position steering gear onto front sub-frame and install retaining nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber and to front stabilizer bar, making sure that the stabilizer bar link is properly positioned. The letters "Top LH" and "Top RH" are moulded into the stabilizer bar link for correct assembly to the front shock absorber strut.
  1. Install new nuts and secure stabilizer bar link assembly to front stabilizer bar and front shock absorber. Tighten to 77-103 Nm (57-75 lb-ft) at front shock absorber strut and 47-63 Nm (35-46 lb-ft) at front stabilizer bar.
  1. Remove safety stands.
  1. Lower vehicle.

Apr 11, 2009 | 1995 Ford Taurus

1 Answer

Problem with front struts


the website "suncore industries" can help you

Apr 10, 2009 | 1995 Lincoln Continental

1 Answer

'99 Lincoln Conti Front Suspension


yes. try this website they have replacement parts.
Suncore industries dot com

Mar 13, 2009 | 1999 Lincoln Continental

1 Answer

99 PASSAT KNOCKING NOISE


If you drive rough roads regularly, you may have a blown shock absorber. You can test it to get a little idea of whether this has happened by using an oldtimer's method that isn't very precise but can help:
From the front of the car, cause each side (one at a time) to bounce by pressing then letting go repeatedly on a fender. When you let go, do it at the bottom of the bounce and note what the fender does. If it rises once, falls, then stops, it is probably OK. If it kind of fades away, then the shock isn't having any influence on it and must be replaced. I should say both should be replaced; never only one.  As warned, this isn't an absolute test but you can get some kind of a feel for the shocks this way.

Feb 24, 2009 | 2007 Volkswagen Passat Sedan

1 Answer

I have a 99 passat tdi and it has a creak on the front suspension


How old are the shocks in the front. i have the same problem. When i turn left on cold days. Flat mate Mechanic says ball joint. He had ame problem. it sounds like shock though.

Jan 04, 2009 | 1999 Volkswagen Passat

3 Answers

FRONT SUSPENSION NOISE


check the wheel bearings

Jul 25, 2008 | 2002 Volkswagen Passat

Not finding what you are looking for?
2002 Volkswagen Passat Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...