Question about 1997 Jeep Wrangler

1 Answer

Same problem here.

I just started the jeep after it was sitting all summer and now it will not go into gear at all.. When i put it up for the summer, it worked great. no leaks are present and fluid is at good levels. Does the system need to be bled if it has been sitting for a long time? and how do i do this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

It is possible that it lost fluid so just crack the bleeder vavle till fluild comes out, once it comes out close bleeder valce and try to move pedal. if it does not move then get a second person to push pedal all the way to the floor then open bleeder valve until you get solid fluid flowing out of it. then lock the bleader valve and see if the clutch push rod will move.If it does not move then the seals on the master or slave have gone bad and recommend replacing both at the same time.

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine overheats, loses power, starts back up but dies when put in gear


I hate to tell you this but... If it overheated you probably have at the very least blown a head gasket. The best thing to do is run a compression check and that will tell all. Hope that helps

Apr 19, 2017 | 1988 Jeep Wrangler

1 Answer

1996 jeep grand cherokee stalls when i put it in gear the RPM's drop down and it stalls it also acts up when i push on the brakes like its running out of gas. After it stalls it wont start unless i leave...


Try looking at your air filter. You could have a vacuum leak, like you already said. Also, check your coolant sensor and intake air temp sensor, if equipped.

Jan 13, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Put my 1995 jeep wrangler in 4 low to see if it would help when reversing up a snow covered driveway...transfer case shifter won't move out of 4 low...pulled back out of driveway and drove a couple of...


your transfer case shifter is locked on 4 low get under take a look at your sifther link shaft, get a long regular screw driver and push the link-shaft up, to release the gear.

Dec 14, 2010 | Jeep Wrangler Cars & Trucks

1 Answer

I have a 1984 jeep CJ7 that has been sitting for 5 years. I finally had it started and the engine sounds great, but now it doesn't- the jeep-move. I can also just shift the gears without having to depress...


BRAKE FLUID IN THE CLUTCH SLAVE MASTERCYLINDER LEAK OUT OR CONTAMINATED BY IT BEING 5 YEARS I WOULD REPLACE CLUTCH MASTER CYLINDER AND CLUTCH SLAVE CYLINER.PUT IN NEW BRAKE FLUID AND BLEED HYDRALIC CLUTCH SYSTEM.I WOUNDNT TRUST THE OLD UNITS FLUID CONTAMINATED AND SEALS PROBABLY SWOLLEN INSIDE CLUTCH MASTER CYLINDER AND CLUTCH SLAVE CYLINDER.

Aug 06, 2010 | 1985 Jeep CJ7

2 Answers

My jeep wont start!


MOST LIKELY YOU WILL NEED TO REPLACE THE NUETRAL SAFETY SWITCH IT IS THE MOST COMMON CAUSE OF THIS PROBLEM, IT IS LOCATED ON THE TRANSMISSION CASE UNDER THE ARM THE TRANSMISSION SHIFT CABLE ATTACHES TO, SEE PHOTO BELOW.

STANDARD MOTOR PRODUCTS Part # NS113T [NUETRAL SAFETY SWITCH]


bcf8c19.jpg

Jul 14, 2010 | 1992 Jeep Cherokee Limited

1 Answer

Crank, no start 98 wrangler 2.5l


crank sensor likely-may be distributor sensor but my 98 sport was crank sensor situated in bell housing timed by flywheel

Sep 15, 2009 | 1997 Jeep Wrangler

1 Answer

Jeep is hard to get started and dies when you put it in gear


First check battery condition, second was the syc set after install?

Apr 18, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Car not taking off for a few seconds after put into gear


it could be ur trany fillter or ur vacume addvance try a trny service

Jan 12, 2009 | 1996 Jeep Grand Cherokee

1 Answer

2001 jeep wrangler starting problems


check the starter relay first please rate -jeff

Jul 01, 2008 | 2001 Jeep Wrangler

Not finding what you are looking for?
1997 Jeep Wrangler Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...