Question about 2000 Dodge Caravan

1 Answer

Need to figure out how to replace light in the inside of the door.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bulb in the light assembly

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Left rear door open warning comes on and off, sometimes it will be weeks ok, then will say open. can't figure out what wire controls that function, think a wire has a break in door jamb area


The door switches in many GM vehicles are known to do this. Either disconnect the switch or replace it for a quick test/repair. They are relatively inexpensive, and simple to replace. If a new switch doesn't fix the issue, further troubleshooting will need to be performed. When you dismantle the door switch, check to make sure the wiring attached to it is clean, dry, and in good condition.

Mar 14, 2015 | 2003 Chevrolet Silverado 2500HD

1 Answer

I cannot figure out how to turn the inside lights off when the doors are open in my 97 Ford Expedition. When I take my kids to the drive in we like to have the back open for comfort but can't tur


My truck did the same . I used Wd40 on all the door joints,latches,locks and the problem stopped immediately
1997 expedition XLT police model

Oct 17, 2012 | 1997 Ford Expedition

1 Answer

2006 BMW X5 Door open message, inside light goes off & on, and the alarm keeps going off


You have a defective door ajar sensor switch. The switch is located on the door latch of each door inside the door. In order to find out which one is the cause of the false warning a trip to the dealer is required so they can scan the systems control module while the warning is on. If you want to guess start by replacing the drivers door switch first.

May 31, 2012 | BMW X5 Cars & Trucks

1 Answer

Install door latch cable


Technical Instructions
See picture below
1. Remove door trim panel and water shield per
NOTE: Place a strip of masking tape along the edge of door before removing trim panel to prevent scratching the door with the trim panel removal tool.

2. Snap cable housing end from slot on inside door handle assembly and disconnect cable.
NOTE: Use care to prevent bending of cable housing retainer bracket.

3. Remove rear window channel retaining bolt to allow access to door latch.

4. Position a block (screwdriver handle) between the latch and the door inner panel and snap the cable housing end out of slot (towards inner panel) on door latch assembly and disconnect cable at latch.
NOTE: Use care when removing cable housing to avoid bending of the latch. Discard cable.

5. Hook up new cable at latch and snap cable housing end into slot.
NOTE: Make sure the cable housing is fully seated in the slot.

6. Apply a light film of Teflon grease to the barrel end of the cable. See Figure A.

7. Install return spring. See Figure A.
NOTE: Ensure that the push button rod is located between the spring and the door inner panel.

8. Install foam block at latch. See Figure A.

9. Position water shield over the return spring and install push pin to retain upper portion of water shield. See Figure B.
NOTE: Push pin goes in the same hole as the return spring.

10. Clean hands of grease before performing step 11.

11. Remove protective backing along the lower edges only of the water shield. See Figure A.

12. Install latch water shield at door latch. Pinch the exposed adhesive surfaces together to secure the water shield. Check to insure water shield is not showing through the door shut-face latch access hole. See Figure B.

13. Attach cable to inside door handle assembly and snap cable housing into slot.
NOTE: Make sure the cable housing is fully seated.

14. Check the gap as shown in remote control using a 3/16 drill bit shank end. The drill bit shank should fit in the gap without any clearance and a tight fit is preferred. See Figure C.

15. If the drill bit is too loose or does not fit, adjust by bending the cable bracket as required.

16. Place plastic wedge on remote bracket as shown. Wedge must fit with at least a light press fit for retention. See Figure D.

17. After installation, Apply a dab of special Teflon grease, supplied with the service cable to cable housing openings at inside handle end. The grease should surround and contact the cable all the way around, to seal the opening between the cable and the cable housing.

18. Check all latch functions to insure correct assembly of latch system. If the inside handle does not release properly, replace the inside handle remote release mechanism.

19. Reposition and install trim panel using new push pins if required.


emissionwiz_53.jpg

Dec 07, 2010 | 1993 Ford F250

1 Answer

2001 Sequoia, door ajar light goes off, but dome light stays on. Door ajar light comes on with slight pressure against closed door. Can replacing the door jam switch solve this problem? Why would the door...


To temporarily solve the light problem, I taped a washer to the inside of the door where the door hits the plunger on the light switch. A permanent solution would be to drill a hole in the door at this spot and put a self taping screw in that will trigger the switch sooner. I figured out the reason the dome light stayed on is due to the courtesy light timer and the lights would have eventually gone off.

Nov 12, 2009 | 2001 Toyota Sequoia

1 Answer

Door Ajar light wont go off.


replace the relay for the courtesy lights. the relay should be under the dash in the fuse panel on the drivers side. if you can't figure out which one. just put your finger on each one till you find the hottest one by touch.

Sep 06, 2009 | 2004 Buick Rendezvous

1 Answer

Cant figure out what the door latch rod hooks to at the latch ins


Rod connects to latch on one end and handle on other end. Remove the inner door panel and look carefully with a light. The clip that holds it on is likely laying inside the bottom of the door. It's a really simple setup and shouldn't be hard to figure out. If you can't, remove the other side and take a quick look.

Apr 07, 2009 | 1985 Chevrolet Nova

1 Answer

Brake lights out


on the inside of right rear and left rear interior panels should be two doors that you open and you can get to the bulbs.

Dec 12, 2008 | 1998 Mercury Villager

Not finding what you are looking for?
2000 Dodge Caravan Logo

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...