Question about 2001 Ford Ranger Regular Cab

1 Answer

How do you remove the third brake light cover on the cab of an 01 ranger

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

On either end of the 3rd brake light housing, there will be a screw. Just remove these screws and the housing will slide right out. Then you can just pop the bulb out

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do I remove the entire cover or the little door thats atached to this cover on the passenger side? There are 3 brake lights that were recommended to replace. Driver side and passenger side plus the third...


Lamp, Rear Hi-Mount Lamp Assembly
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Raise the liftgate.
  1. Remove the liftgate door trim panel (46404) . Refer to Section 01-05 for the removal procedure.
Trim Panel, Liftgate Door Removal
  1. Disconnect thebattery ground cable (14301) .
  1. On vehicles with a rear window wiper, remove the three rear wiper motor cover screws and remove the rear wiper motor cover.
  1. Pry the liftgate door trim panel (46404) away from the liftgate.
  1. Disconnect the luggage compartment lamp electrical connector.

    n11098a.gif

  1. Remove the liftgate door trim panel
  1. Rotate the rear hi-mount lamp socket counterclockwise and remove it from the rear hi-mount lamp (13A613) .

    k20521a.gif

  1. Remove the two rear hi-mount lamp housing nuts and remove the rear hi-mount lamp lens and housing.

    k20523a.gif

Oct 18, 2010 | 1995 Ford Aspire

1 Answer

Brake lights work, but 2001 Ford ranger will not come out of Park.


The shift actuator releases the shifter lock when the brakes are applied, if the actuator is faulty it will not release the shifter. You can test the actuator using a test light to make sure that it's getting a 12V input when the brakes are applied, if so then look to see if the actuator is moving. If you have a 12V input but no movement then you can remove the actuator and us a volt ohm meter to test the Actuator or a 12V battery. This can also be removed but i do not suggest this! It is a great safety feature.

Jul 29, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

01 chevy silverado tail lights problems


CHECK THE LIGHT YOU CHANGEIT IF THEY SEE FINE AND THE FILAMENT IS INTACT CHEK THE CONECTCION PLUG OF THE BRAKE LIGHT AND WITH A SCREW TRY TO CLEAN THE CONECTION ARE SOMETIMES WITH THE CONSTACT USE GETS A LITTLE BIT RUSRTY BUT NOTHING IMPORTANT

Mar 29, 2009 | 2001 Chevrolet Blazer

2 Answers

My third brake light dosen't work on my chevy s10 94'


I had a similar problem with my 1994 S-10 LS extended cab. Both tail brake lights worked fine. I removed the 3rd brake light cover and tested for voltage at the steel center of the two rivets and found the positive (driver side) negative (passenger side) were good. I checked the two metal strips that send power to bulbs and found the positive side was open. Seems the flared side of the rivet was not making contact with the metal strip. I bucked the rivet with a punch and hammer and it took care of the problem.

Mar 17, 2009 | 1994 Chevrolet S-10

2 Answers

Need to replace cargo & third break light how do i


if its the same as an 06 Tundra, you should be able to remove the lense cover from the back of your truck cab with a screwdriver and pull the light bulbs out...Do not remove the screws below the lense cover that removes the fixture, they have a screw insert that will fall into your truck's body and get lost.....hehehehe I learned that from my own experience...good luck!

Mar 04, 2009 | 2008 Toyota Tundra

1 Answer

2001 ford ranger no brake lights


check fuses under the dash and in the engine compartment/ Please rate my response thank you very much

Feb 01, 2009 | 2001 Ford Ranger Regular Cab

2 Answers

Wet Headliner


You likely have a water leak around the 3rd brake light mounted on the top rear of the cab. I had this same issue on my 96 Ranger Supercab and found that the foam seal had gone bad and was allowing water to leak into the back of the headliner around the light fixture. It ended up soaking the headliner from one side to the other as the headliner acts as a 'wick'. You can repair this issue by either replacing the sealant around the 3rd brake light or replacing the brake light. There are two screws which secure the 3rd brake light assembly to the back of the cab. Remove these and it will pop right out. I upgraded mine to an LED light when I replaced it. That solved two issues at once as I'll never need to change a bulb there again. If you want to be cheaper you can not replace the light and just seal it with rubber silicone sealer.

Jan 14, 2009 | 1990 Ford Ranger SuperCab

1 Answer

Rear brake light function not working


Hi
You may just have a bad earth in wiring on the lighting or your light control modual could be fuilty has any one tested this for you
Paul

Dec 31, 2008 | 1996 Lincoln Town Car

1 Answer

2003 Ranger FX-II ABS light on


This isn't hard to do at all really and should be easy to procure the part from the local parts store. There is only one little screw holding it in

102969669

  1. Raise and support vehicle.

  2. NOTE: Clean off dirt and foreign material that may have collected around the rear anti-lock brake sensor before removal. Remove the rear anti-lock brake sensor.
1 Disconnect the rear anti-lock brake sensor electrical connector. 2 Remove the bolt. 3 Remove the rear anti-lock brake sensor.
  1. NOTE: Thoroughly clean the mounting surface. NOTE: Inspect the anti-lock brake sensor O-ring for damage; lightly lubricate the O-ring with axle lubricant. To install, reverse the removal procedure

Nov 05, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
2001 Ford Ranger Regular Cab Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...