Question about 1995 Honda Odyssey

3 Answers

Brake pedal going to floor need help finding out what it is

Posted by on

  • christoph637 Oct 05, 2009

    need help fast have appiontment tomorrow


3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,187 Answers

Most likely there is air in your brake lines. You must have them bled.
I have yet to find a good brake shop that can do this right. Make sure they road test it. If it doesn't work right when you drive it, take it back and make them do it right or get a refund.

Your master brake cylinder can also be worn; however, the pedal will sink to the floor slowly and you will be able to "pump" the brake pedal.

Posted on Oct 05, 2009

Testimonial: "thanks"

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Needs Masterbrake Cylinder. Its Located Drivers side firewall. MAKE SURE! To Inspect all, Brake lines and connections are NOT leaking brake fuild. Note: If you can pump the pedal and get stopping power. More than likely. Its the Master Cyliner. It is bye passing fulid internaly. A rebuilt is cheep. And will work fine. Core charge will apply, take the old one with you to buy a new. Later Mike Naylor

Posted on Oct 07, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

You either have a hole in one or more of your break lines or your master cyllender is leaking/damaged

Posted on Oct 05, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

On a 97 gmc truck when you push the brake you can hear air from the brake booster into the cab of the truck and brake travels freely to the floor

When a vehicle is turned off, the brake pedal should remain firm. However, if the driver pushes the pedal lightly and it sinks to the floor, the master cylinder has an internal leak.

Feb 17, 2017 | GMC Cars & Trucks

1 Answer

No brake pedal w/ running car

If your brake pedal is going to the floor, you either have air in your lines and need to bleed all four wheels, or you have a serious leak somewhere, which should be easy to find by having someone pump the pedal while you look underneath. Fill the reservoir first..

Nov 22, 2016 | Cars & Trucks

4 Answers

Brake pedal goes to floor vehicle still stops

Is the brake light on? Check your fluid level. Pedal going to the floor could be because of a leak in the hydrolic system line, hoses, caliper, wheel cylinders, master cylinder internal and external leaks. Can also be because of over sized drums and/or under adjusted brake shoes.

Jun 13, 2014 | 2000 Chevrolet Blazer

3 Answers

2005 chevy duramax 4x4 brake pedal goes all the way to the floor, ABS light on

You need to add BRAKE fluid. After that, blead your brakes. You need to find out where the brake fluid went. If there are no leaks, you need to check the remaining life on all four brake sets. If you have no leaks, chances are pretty good that you need new brakes.

Dec 14, 2012 | 2005 Chevrolet Silverado 2500HD 2WD

1 Answer


if a master cylinder is bad and you are sure you have all the air out and no leaks.pedal will go to floor , running or not. if booster is bad it will cause a hard pedal. but if master cylinder is bad it will turn on a brake light on dash if it works. make sure the wheel cylinders are not leaking. I beleive that the master cylinder is bad, or you have a leak somewhere. If the master cylinder is functioning properly, the brake pedal will depress to a certain depth and no further.

Apr 20, 2012 | 2000 Chevrolet Blazer

2 Answers

On my 1986 ford escort the breaklights wont turn off

Check the brake pedal's suspension; you should find the brake light switch there and it has either failed or its mounting bracket needs to be adjusted.

Aug 23, 2011 | Ford Escort Cars & Trucks

1 Answer

II was changing my brake pads and accidently unscrewed the bolt to my break fluid. I finished the pads and went to set the brake and it just went to the floorboard and checked brake fluid. the resivoir was...


Oct 20, 2010 | 1999 Nissan Pathfinder

1 Answer

How to bleed the brakes after you replace rear brake lines

hi, if you look at the back of the brake drum you will see a little bleed nipple just sticking out think its an 8ml or 10ml spanner fit, what you then need to do is find a piece of plastic pipe that will fit over the top of this to catch any fluid then make sure the brake fluid is topped up, you then need someone in the car to operate the brake pedal and some one at the back where the bleed nipple is once you have this you need to do the following

1 undo bleed nipple a couple of turns
2 get person in the car to push brake pedal to the floor and hold it on the floor.
3 when pedal is at floor tighten the bleed nipple up and get the person to let the brake pedal come up.
4 when pedal is up all the way undo bleed nipple and get person in car to push pedal to floor.
5 when pedal at floor tighten bleed nipple up
6 let pedal up
7bleed nipple undo a bit
7 pedal down to floor
8bleed nipple do up
9 pedal up
10undo bleed nipple

now keep doing that until all you have got coming out is fluid and no air when you have this do bleed nipple up and check the brakes to make sure they are not spongy.

whilst doing this you need to make sure the brake fluid level dont drop to low as you will have to bleed the front as well so keep checking the level and make sure its well topped up throughout the whole process

if you have any problems give me a shour back ok

Aug 14, 2010 | 1998 Chrysler Cirrus

1 Answer

1993 Mercury Grand Marquis, Brake fluid leaking under left rear door. Brake pedal goes to floor. How can i fix this?

Hi, the reason the pedal goes to the floor is because the brake line going back to the rear axle blew, first you will need to find where the hole is and cut out the bad section, usually you can find a clean spot further down that you can cut out the bad spot. you will need to go to the parts store and get a new piece of brake line and a tubing cutter and a double flare kit. usually you can rent one of these to save money.

May 22, 2010 | 1991 Mercury Grand Marquis

Not finding what you are looking for?
1995 Honda Odyssey Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides