Question about 2000 Hyundai Elantra

1 Answer

Heater doesn't work?

Even when my car has been warmed-up and driven and is at optimal temperature, I cant get heat inside. It only blows cold air. Radiator and reservior are both full of antifreeze/coolant and all controls are set properly inside. Not sure if it matters, but the ac did work this summer.

Thank you

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 140 Answers

Your thermostat may not be working properly. Coolant flows thru your heater core where the blower motor blows that heat from the coolant thru your vents. If the coolant is not warm enough wich is a sign that your thermostat may be stuck open or opening too soo, your air may be colder than normal.

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Heater temp on high only bows luke warm air after driving. A/C works just fine.Plenty of cold air from it


heater blows cold air idle chrysler 300 Questions & Answers ...

www.fixya.com > Forum > Tags
Find solutions to your heater blows cold air idle chrysler 300 question. ... blow warmair for a few mins then back to luke warm. i replaced thermostat ... HEAT BLOWSCOLD AIR WHEN IDLING ONLY GETS HOT WHEN START DRIVING ... About 15 minutes after driving the diver side vents start blowing straight cold air but the ...

Heater only works when pressing the gas? - DoItYourself.com ...

www.doityourself.com/...repairs.../459521-heater-only-works-when-pres...
Nov 3, 2011 - When I press the gas, the air from the vents is nice and hot. .... So am Idriving a car with a ton of problems, or could the power steering ... Just anotherquestion, when warmed up does the engine temperature ... When the heater is on and I'm not pressing the gas pedal, luke warm air blows from the vents.

Heater blows cool air when stopped and warm air while ...

https://www.reddit.com/.../heater_blows_cool_air_when_stopped_...

RedditFeb 12, 2014 - Heater blows cool air when stopped and warm air while driving 2008 Kia Spectra (self. ... just fine but appears to blow cool air when I was stopped at a stoplight. ... My temp gauge would also be pegged high when at idle / low RPM. ...thermostat only blocks coolant going to the radiator, and the heater core, ...Missing: 300m ‎luke

Why is My Car AC Blowing Hot Air? - BlueDevil Products

gobdp.com/blog/car-ac-blowing-hot-air/

Jan 27, 2016 | 2000 Chrysler 300M

1 Answer

Heater blowing cold air


the blend doors or the one way checvalve is not workin--their vacuum operated but the doors are motor driven also--its a job to get into the dash--need a repair book etc-mite wanna take to a good independent--since its electic related try disconnectn batt or unplugn computer fora min and see if it clears

Dec 24, 2013 | Mazda B3000 Cars & Trucks

1 Answer

2008 peugeot 308 1.6 sport, temperature reads normal,but heater only blows very slightly warm air.


There can be all sorts of other DIY's from draining, flushing and refilling system, thermostat replacing and buying a new car.
Mine from City Peugeot was going to be a £2000 fix and they didn't even know what was wrong.It was just a hail Mary.
Other things that beat them was the rear light cluster not working - £400 fix, was just a loose fuse in the glove box.
The 26mpg when it should be 43, they just say is in the ok bracket, even though I reported it within 2 months of buying and it was sold as 43mpg.
Best advice - do not buy another Peugeot. I now cycle everywhere unless it is raining. I stay local and cant afford another car. Thats all fair I suppose.

Jan 20, 2013 | 2008 Peugeot 308 1.6

1 Answer

Heater blows cold air


Air Temperature Control Blend Door Failure No Heat

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Nov 01, 2012 | Pontiac Cars & Trucks

1 Answer

No heat air is blowing cold


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is worm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest to flush the heater core.

Oct 22, 2009 | 1998 Ford Taurus

1 Answer

MY 1998 FOR TARUS HEATER WILL NOT WORK.WAS DRIVING


It is most probably the problem with blend door or blend door actuator. But just in case I would suggest to follow the entire procedure:

First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

Heater not working


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

Heater only blows cold air but hoses are hot


Hi!
It appears we have an Air lock scenario and you will need to perform a system Bleed.
Park the vehicle on level ground, when cold remove coolant filler cap, start engine and leave to idle, turn heater on full and blower to max. When engine reaches operating temperature watch and listen near coolant filler, keep clear as gurgling and hopefully a boil over should occur. Top up with very warm coolant and wait as it may do it again.
Check for heat inside vehicle if warm replace coolant cap but keep an eye on temperature gauge as the ~Air lock may have moved on from heater matrix/core so proceedure needs to be carried out again from COLD.
If persistent boil ups/over attention must made in the cylinder head
or gasket area, or possibly water pump?
Please press the Blue button to appraise my FREE Efforts, Thank You!
Paul 'W' U.K

Feb 28, 2009 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
2000 Hyundai Elantra Logo

862 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...