Question about 1988 Isuzu Trooper 2 Door

1 Answer

Front drive shaft removal for 2001 izuzu trooper 4x4

It is passenger side. i have everything out of way from the shaft. what i need to know is that rather i just pry shaft out or do i need to remove a plate first then pry out
??

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 235 Answers

Under the rubber boot inside the CV joint is a big spring clip round the edge , take this out and then the shaft pulls away from the axle with the CV on it .If you are fitting a new boot cut the old off if not just get the clips off and pull the boot back.

Did you take the shaft out from the wheel hub end too ?

Posted on Oct 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

Trying to remove drivers side front c.v. shaft on 2001 gmc jimmy 4x4. everything taken apart but shaft wont seperate from transf.case do i need to take out the 5-6 bolts surrounding the shaft on the...


yes the bolts will need to come out and they still stick on there pretty good i have needed to use a chisel and hammer and tap were they are connected good luck
chris

Mar 11, 2011 | GMC Jimmy Cars & Trucks

1 Answer

How to check fluid for transmission and clutch in a 4x4 5 speed 1989 izuzu trooper


transmission include:gear box,front differential,and rear.all have fill up bolt.the bolt is the level.the clutch reservoir is next to the brake one.(some models use the same one)

Jun 09, 2010 | 1989 Isuzu Trooper

1 Answer

"Auto" light on the Torque on Demand for my 2001 Izuzu Trooper bl


I have the exact same problem. I can lock it in low range with the shifter but the auto push button doesn't work. Hope someone knows something./

Jan 01, 2010 | Isuzu Trooper Cars & Trucks

2 Answers

Izuzu trooper


Its behind a little panel just above the hood release

Dec 14, 2009 | 2001 Isuzu Trooper

1 Answer

Transfer Case not locking in


you need to take it to a garage ,put it on a hoist , start it up ,put it in drive ,put it in 4x4 and see if front drive shaft spins,if it is and the front wheels are not it is most likely the plastic thing on the passenger side of the front axle. This is what locks in the front axle to the drive shaft. If the drive shaft isnt spinning then it is a problem with the transfer case.

Apr 22, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

How do you replace turn signal bulb on 2001 Izuzu Trooper?


NOT SURE IF IT IS TRUE ON THIS KIND OF VEHICLE, BUT USUALLY WHEN CHANGING A BULB YOU NEED TO GO UNDER THE HOOD ON WHATEVER SIDE YOU ARE CHANGING...AND THERE WILL BE A KIND OF PLUG INTO THE BACK OF THE ACTUAL LIGHT FIXTURE, IF YOU GIVE IT LIKE A QUARTER TURN IT WILL PULL OUT YOU THEN CHANGE THE BULB AND PROCEED WITH PLUGGING BACK IN. MAYBE THIS WILL HELP!

Jan 10, 2009 | 2002 Isuzu Axiom

2 Answers

2001 Trooper: Front axle will not engage when I press dash 4x4 switch


hi guys i would check all the small vacume pipes that conect the sol valves toi the vacume actuators having just replaced the engen in mine i found that these do not have any clips holiding them on tight and can get oil on them and become oversized and leak you can test the diaframes in the actuators by putting a length of pipe on one port and sucking by mouth you can hear the actuator move and then find you can put toung on end of pipe and it will hold a vacume if it does not then chances are the actuator diafram id u/s hope this helps bill

Nov 09, 2008 | 2001 Isuzu Trooper

3 Answers

I need to know how to take the front hubs off to replace the rotors on a 1994 Isuzu Trooper.


97460706 Take it apart in the order you see you need some snap ring pliers for item #4 . Take off #7 and the rest of the parts. Seperate the hubs from the Rotors (it may need to go to a machine shop fort this operation) When you reassemble make sure that one of the holes in # 7 line up perfectly with a threaded hole in #8
Make sure you get the wheel bearings tight but not too tight and Grease them properly with the prooper Lube recommeded by Izuzu.
Hand TORQUE the wheel lug nuts as Izuzu has a BIG BIG Problem with wheel lugs stripping USE A TORQUE WRENC

Jul 31, 2008 | 2001 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

724 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...