Question about 1987 Toyota Pickup

2 Answers

My truck wont start or turnover - 1987 Toyota Pickup

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Check battery and all connections and if standard check the neutral safety switch

Posted on Oct 04, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 308 Answers

If the car wont start or turn over there is a problem in the ignition system or assembly of the car . That is why the owner of the car should check on the ignition assembly of the car.Because if the car won't start there is no power in the car that makes the car drive or turn over.But the owner of the car should be able to locate the and check the ignition system.Prepare the tools and equipment to be used in checking or servicing the ignition assembly.So that when the ignition system is checked it will function properly.Then you have to locate the parts of the ignition system:Ignition switch ,ignition coil, distributor assembly,spark plug. you have to check check corroded switch,check ignition coil. Check distributor assembly: contact point gap,condenser.check the high tension wires and terminals. check wires and connections.check spark plug gap.Observe all safety rules.If there are worn out or malfunctioning parts there for you have to repair them or if not any more functioning replace them.If the owner don't have time to do the fixing of the problem of the car there fore the owner of the car should go to a car shop mechanic and let the mechanic do the job.

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Aztek wont turnover. Lights battery starter new, no sound from the starter Stuck in park too Then it starts Tow truck lets it down, and it starts, until later then it happens again.


Try turning the stop sensor clockwise a quarter turn. If you follow the brake pedal up you will see the two with plungers the brake hits when you depress the brake.

Feb 26, 2017 | 2003 Pontiac Aztek

1 Answer

2004 chevy s10 zr5 wont start


How old is battery and clean connection.Could have 12.5V but do not havecrank power.

Aug 21, 2014 | Cars & Trucks

1 Answer

Fan belt was tightened, now wont start on first turnover,will start on prolonged second turnover. 00 range rover 2.5 dse


No, no timing adjustment should even be considered. Maybe the belt is too tight. Have the tensioner pulley checked, if this is a serpentine belt.
You might try loosening it just a bit, if possible, and see if previous performance returns.

Jun 18, 2012 | Cars & Trucks

1 Answer

2006 hummer h3 wont start wont crank


Check the main power fuse of 100watt

Feb 05, 2012 | 2006 Hummer H3

1 Answer

Engine wont turnover until after second or third try


Could be a bad connection at the positive or negative terminals of the battery. I had this problem on my 1997 Cadillac Deville where it would click, or do nothing, and if I toggled the starter through the ignition switch, then it would start on the third or fourth or fifth try.

I thought it was the security system, but it turned out that wire brushing the connectors at the battery (after they were removed) solved the problem beautifully.

Aug 03, 2010 | 2001 Lincoln LS

1 Answer

The truck was sitting for about 10 years, everything electrical works, i replaced the spark plugs, wires and rotor before even trying to turn it over, the engine wants to turnover and the spark plugs are...


if its carberated, u need to clean that out. if its fuel injected, replace the fuel filter. if it stil dont work. then u have a fuel injector problem

Mar 05, 2010 | 1986 Toyota 4Runner

1 Answer

2002 Chrysler Sebring Convert wont turnover


If you're not hearing a click from the starter check for a starter relay. May be burned out! DO you hear the fuel pump kick in when you turn the key on? If not something might have triggered your security system and locked you out!

Jun 28, 2009 | 2002 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...