Question about 1994 Suzuki Swift

1 Answer

How do I remove 2000 swift automatic transmission

Can I remove the transmission in my 2000 swift without removing the engine?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Suzuki Master
  • 3,433 Answers

Yes

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Is it possible to put a flywheel on without removing whole transmission


No, it has to be completely removed aside. Only then can you get to the flywheel bolts.

Aug 25, 2015 | Cars & Trucks

1 Answer

How to remove1995 cavalier transmission


The transmission is transversely mounted in these vehicles. The mount that secures the transmission to the body is also supporting the engine. If you want to remove the transmission without also removing the engine you will have to support the engine once you remove the transmission mount. You will need to remove the drivers side wheel, caliper, and rotor. You then need to remove the drivers side CV shaft. You will need to separate the lower ball joint in order to remove the shaft and to provide working room to separate the transmission from the engine. You need to disconnect the Shift cable (automatic) or slave cylinder (manual) from the transmission. You must separate the passengers side CV shaft from the transmission, but you do not need to full y remove it. Ensure that you do not separate the inner CV joint when pulling the transmission free from the inner splines. Remove the flywheel shield plate. If automatic transmission, unbolt the torque converter from the flywheel. Disconnect any electrical connections from the transmission. If automatic transmission, disconnect the hydraulic lines running to the radiator. Unbolt the transmission from the engine at the bell housing. Automatic transmissions will come out fairly easy...manuals you must pull back to disengage the transmission splines from the clutch disc.

Sep 07, 2014 | Cars & Trucks

1 Answer

How to replace main bearings on 2.2 chevy cavalier 2000 without having to pull the engine out


You can't. To replace the main bearings you need to remove the crankshaft. To remove the crankshaft you must remove the flywheel. To remove the flywheel, you must remove the transmission. The transmission is part of the engine mounting system. Just buck up and pull the whole works. Chances are you will need to re-bore the mains anyway if you have spun any of the main bearings. That cannot be done with the engine in the car.

Aug 02, 2014 | 2000 Chevrolet Cavalier

2 Answers

Can a 2000 kia sephia transmission be removed without taking the transaxles and exhaust line off?


when in doubt , thank politely and go some where else to an accredited service shop that has experience on your make of vehicle
on assembly the power train ( engine and transmission) is on a stand and the body is lowered down over it and all of the subframe bolts are screwed in
so yes it is possible to remove the power train complete but as that would be the quick way to do it
I suspect that something more sinister is afoot
did you get a detailed explanation of the transmission problem or axle problem or was it just "you need a new " comment

May 01, 2017 | Kia Sephia Cars & Trucks

1 Answer

Need to replace oil pan on a bmw 2004 330ci


Raise engine with special tool 00 0 200 approx. 5 mm.
- Remove suction filter housing. Remove engine splash guard.
- Drain engine oil. On vehicles with automatic transmission:
- Disconnect oil lines from automatic transmission and from oil pan.
- Release guide tube for dipstick.

Note: M52TU and M54 only.
- Detach return hose from cyclone oil separator on oil dipstick guide tube.
- Replace O-ring.
- Remove front end reinforcement.
- Detach steeling spindle from steering gear.
- Remove vane pump for power steering unit (lines remain connected).
- Disconnect plug connection to oil level sensor.
- Loosen top and unfasten bottom of left and right engine mounts.

E46 4WD only
- Remove left and right swivel bearings.
- Remove output shafts. Remove front propeller shaft.
- Remove front axle differential.
- Detach brackets for left and right control arms from engine carrier.
- Release retaining brackets for left and right stabilizer bars.
- Unfasten screw connection on front axle support and lower the front axle support.

Note: There is no need to detach the steering gear from the front axle support.

- Unfasten oil sump screws at transmission and engine ends.
- Lower and remove oil sump.
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agent to the area around seams.

Installation:
  1. Replace gasket
  2. Install oil sump.
  3. Insert all oil sump screws.
  4. Insert screws in transmission end without preload at this stage.
  5. Tighten down screws in engine end.
  6. Tighten down screws in transmission end.

E60 Removing And Installing, Sealing Or Replacing Oil Sump (M54)

Necessary preliminary tasks. -
- Remove intake filter housing
- Remove guide tube for oil dipstick
- Lowering front axle support
- Drain off engine oil
- Disconnect plug connection to oil level sensor.

On vehicles with automatic transmission:
- Detach oil lines from automatic transmission and from oil pan.
- Unfasten oil pan screws at transmission and engine ends.
- Lower and remove oil pan.

Installation:
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agen to the area around seams.

Installation:

  1. Replace seal.
  2. Install oil sump.
  3. Insert all screws on transmission end, without preload at this stage.
  1. Tighten down screws on engine end.
  2. Tighten screws on transmission end.

Or take it to a dealer....

Apr 19, 2011 | BMW 330 Cars & Trucks

1 Answer

How hard is it to change the transmission and torque converter in 2001 honda odyssey 4 speed automatic 3.5 liter v6? do you have to remove the engine to do so?


you need to remove the whole transmission unit from the vehicle without removing the engine. It is quite tough and the transmission unit is quite heavy. you need to remove the suspension frame underneath the vehicle and the drive shafts as well.

Apr 20, 2010 | 2001 Honda Odyssey

1 Answer

Fluid capacities and fluid specs


2000 TOYOTA TACOMA 2.7L 4-cyl Engine Code 3RZ-FE

Engine Oil Grade 1......API* All TEMPS......5W-30 Optional ..10W-30
Engine, 2WD, with filter..........5.5 liters
Engine, 4WD, with filter..........5.4 liters

Manual Transmission,......GL-5/ GL-4 All TEMPS......75W-90
Automatic Transmission,A340E......AF3 / A43D......AF3

Differential, Front/ Rear W/ ADRD......GL-5 ALL TEMPS......75W-90
Differential, Front Less ADRD......GL-5 ALL TEMPS......80W-90

Transfer Case,......GL-4/GL-5 ALL TEMPS......75W-90 Gear oil.

Capacity:
Cooling System, Initial Fill..........8.5 liters
Automatic Transmission, A340E Initial Fill..........1.6 liters
Automatic Transmission, A340F Initial Fill..........2 liters
Automatic Transmission, A43D Initial Fill..........2.4 liters
Automatic Transmission, Total Fill
4 speed A340E..........7.2 liters
4 speed A340F..........10.1 liters
4 speed A43D..........6.5 liters
Manual Transmission, ..........2.5 liters
Differential, With ADRD Front..........1.2 liters
Differential, Without ADRD Front..........1.1 liters
Differential, 2WD V6 Rear..........2.6 liters
Differential, 4WD Extra Long Rear..........2.5 liters
Differential, Short WB With LSD Rear..........2.7 liters
Differential, Short WB Without LS Rear..........2.6 liters
Transfer Case, Electronic..........1.2 liters
Transfer Case, STD..........1 liters


Feb 09, 2010 | 2000 Toyota Tacoma PreRunner

1 Answer

2000 Chevrolet Tracker How do you remove the transmission pan?


that is the filler tube for the tranny
just pull it straight out when your done put your pan back on then push it down in there and make sure it is seated all the way
good luck ray

Jan 20, 2009 | 2000 Chevrolet Tracker

Not finding what you are looking for?
1994 Suzuki Swift Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...