Question about 1998 Mercury Mountaineer

1 Answer

How to replace blower motor in 98 mercury mountaineer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Autozone Chilton manual step by step info on this 10.00

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need help find the location of blower resistor


Blower Motor Speed Controller is located near the blower motor per the shop manual...

Sep 20, 2014 | 2000 Mercury Mountaineer

2 Answers

1999MERCURY MOUNTAINEER AC BLOWER ONLY RUNS ON HI SPEED? WHAT TO DO?


blower motor resistor is burnt up
located upsteam in air plenum from blower motor
passenger side compartment at foot
locate motor then you should spot resistor close by

May 09, 2011 | 1999 Mercury Mountaineer

1 Answer

Need to locate the motor blower resistor for my 1999 mercury mountaineer, it has dual air, the resistor for the back is fine but the one in the front is bad and i cannot locate it. Please help.


If you have a manual system, you have a resistor. If electronic, you have a blower motor speed controller. Please rate if this helps.

here is info:

Control System Outputs-Manual A/C
Blower Motor Switch Resistor
The heater blower motor switch resistor has the following features:
  • The assembly is located on the evaporator housing in the engine compartment.
  • Three resistance elements are mounted on the resistor board to provide four blower motor speeds.
  • Depending on the heater blower motor switch position, series resistance is added or bypassed in the blower motor circuit to decrease or increase blower motor speed.
  • An overheating protective device (thermal limiter) will open the resistor coil circuit when the temperature reaches 121°C (250°F) interrupting the blower motor operation in all speeds except HI.
  • The thermal limiter cannot be reset and is not serviceable.
Control System Outputs-EATC
Blower Motor Speed Control
The blower speed control is located on the evaporator housing in the engine compartment.
  • The function of the blower motor speed control is to convert low power signals from the electronic automatic temperature control module to a high current, variable ground feed for the blower motor (18527).
  • The blower motor speed is infinitely variable and is controlled by the electronic automatic temperature control module software.
  • A delay function provides a gradual increase or decrease in blower motor speed under all conditions.

Jan 10, 2011 | 1999 Mercury Mountaineer

1 Answer

How do i change a blower motor in a 1999 mercury cougar


Blower Motor Removal
  1. Remove the footwell upper trim panel (passenger side).
    • Remove the pushpins.
  1. Remove the blower motor.
    1. Disconnect the electrical connector.
    1. Lift the securing tab, turn the motor approximately 30 degrees counter-clockwise and remove the motor.

Jan 10, 2010 | 1999 Mercury Mountaineer

1 Answer

Heater/AC Blower Resistor Module


it goes just to the right of the blower motor.

Mar 27, 2009 | 2002 Mercury Mountaineer

1 Answer

Can anyone help with an intermittent starting issue with a '98 mercury mountaineer?


If the motor turns over, but not start. Have the "crank shaft sensor" checked/replaced Ford part# 184768 $27.98 parts $230.00 labor). I chased this problem for several years. The crank sensor finally failed completely and the mechanic was able to find the problem.
Good luck

Jan 12, 2009 | 1998 Mercury Mountaineer

Not finding what you are looking for?
1998 Mercury Mountaineer Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...