Question about 1990 Dodge Dynasty

2 Answers

Dodge Dynasty 1990, 3.33 liter eng. The belt

Dodge Dynasty 1990, 3.33 liter eng. The belt continues to slip off of the power steer pulley or all of the pullies. Can't seem to keep it on.

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers


Posted on Nov 16, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Dodge Master
  • 2,002 Answers

Check to see if all your pulley's are aligned properly. It sounds like they may not be. Put the belt back on and look straight down it. If it appears to have a bend, that needs to be fixed. If you have a carpenter's square you can use it to double check you eye. You can use washers as shims on the bolts that hold whatever is out of line. If it sticks out too far you'll have to grind or file it to bring it back in line or remove washers or spacers if there are any. Hope this helps.

Posted on Oct 05, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace power steering belt

You should have a serpentine belt (one continuous multi-grooved belt) on that model in which case the easiest way is to get (or borrow) the special tool (a long bar with a place to install a socket) to back the tensioner off enough to slip the belt off one of the pulleys. Install in the reverse order using the wrench back the tensioner pulley back enough to get the belt over the last pulley then release the tensioner - it will automatically provide the proper tension. If it a single V-belt then look for a bolt or bolts you can loosen and slide the power steering pump toward the motor and remove the old belt then install the new one, carefully pry the pump back into place and tighten the bolt(s). This should work on most vehicles.

Apr 30, 2014 | 1991 Dodge Dakota

1 Answer

Serpintine belt will not stay on

Something is not turning correctly. Could be a water pump or a loose tensioner. Check to see if everything is easy to rotate...alternator, power steering pump, A/C pulley water pump. Do this with the belt off.

Jan 10, 2014 | 1990 Dodge Dynasty

1 Answer

How to intall motor belt

for a 5.7 liter, start a the crank pulley,go clockwise around the waterpump pulley,go downto the power steering pulley,up to the a/c comppressor,under the idler pulley,up to the alternator pulley,and the slip the belt onto the tensioner pulley.

Jun 09, 2012 | 1997 Chevrolet Suburban

1 Answer

My serpentine belt broke while driving, I replaced the belt but the belt drifts or slips a little at the bottom large pulley, so I changed the power steering pulley since it seemed to have some play in it...

you could adjust your tensioner to fix it, but most likely your power steering pumps pulley is not completely parallel with the the crank pulley

Nov 23, 2009 | 1999 Dodge Dakota

3 Answers

Serpentine belt diagram for a 3,3l dodge dynasty with ac

For the 1991 DODGE DYNASTY - V6 3.3L 201ci GAS FI N R , review this informacion:

Belt Routing Diagram
- Multiple Accessory, w/o A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/o A.C. (Mfg. Before 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. Before 2/27/91)

Remove the serpentine belt by using a breakover bar, rachet or serpentine belt removal tool with the correct size socket for the pulley mounting bolt. Rotate tensioner arm to release tension. Remove the belt.

Hope helped with this (remember rated this help) Good luck.

Nov 12, 2009 | 1991 Dodge Dynasty

2 Answers

Water pump location on 93 dodge dynasty 3.0 v6

The water pump is located behind the timing belt cover and is run by the timing belt itself.This is a big job good luck:)

Aug 31, 2009 | 1992 Dodge Dynasty

1 Answer

1990 Dodge Dynasty, has severe problems with the pulleys. Belt continues to slip off of the pulleys. Why does this little car have 5 pulleys and they don't do the same thing???

make sure, with the belt off, that all the pully spin VERY freely. sounds like a component with a pully is locked up. good luck.

Jul 17, 2009 | 1990 Dodge Dynasty

1 Answer

Cant get old one off to replace it with the new one

Had the same problem, but it was the power steering pully, you have to get it from up under the car, it will be pretty hard to get the belt tensioner tool through there, but can't get it from up top.

Apr 22, 2009 | 1990 Dodge Dynasty

2 Answers

Odometer and belt tensioner

if your still having belt problem the harmonic balancer may be bad and sooner or later will fall apart. as for the odometer the cluster may be bad, as mine is or the sensor at the trans may be bad

Jun 14, 2008 | 1992 Dodge Dynasty

Not finding what you are looking for?
1990 Dodge Dynasty Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides