Question about 1994 Toyota Supra

Open Question

How to install fuel rail and injectors for supra? do i have to remove my intake?supra twin turbo i am going to upgrade to 880cc injectors

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75066 Answers

SOURCE: Fuel rails/injectore removal

they just pull out, replace the O ring seals on each injector before reinstalling, also put Vaseline on the O ring seals before installing them to prevent damage.

Posted on Feb 16, 2009

  • 83 Answers

SOURCE: i have no power to my fuel injectors on 88 saab 900 turbo

There should always be power at the injectors as long as the fuel pump is on. The fuel injection ECU provides a ground to the injectors to turn them on.
You most likely have a bad fuel injection ECU. This is a very common failure on 88,89 and 90 SAABs.

Posted on Mar 25, 2009

  • 3600 Answers

SOURCE: flooded engine on 96 turbo supra

Hold the throttle all the way to the floor crank until it runs, with the pedal all the way to the floor this puts the car into Clear flood mode.

Posted on Jul 08, 2009

  • 274 Answers

SOURCE: citroen saxo 1.6 vtr has fuel injector problem

hi mate if you look on the n/s/f strut mount under the bonnet there should be a black unit with a red top on it. this is the fuel cut-off switch, press the center of the red cap, if it clicks then it means it has been activated (usually by being knocked)

Posted on Dec 07, 2009

  • 11 Answers

SOURCE: 1995 jetta 2.0 fuel pump

ok could be a few things.

Have you changed the inline fuel filter? these usually have paper filter elements and after a while can be clogged with moisture which blocks fuel flow. The fuel pump will still have good pressure but the fuel rail will lack the flow required and you may burn out an injector as its running too lean. Secondly, the MAF sensor, could be dirty, clean it with electrical cleaner.

I think its more likeylt the fuel filter blocked. Try and bypass it if possible, reset the ECU and try agiain

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the fuel injector for a 2008 chrysler pt cruiser?


To remove a fuel injector or injectors you must remove the fuel supply rail that sits over them. Here is how you do that for both engine options, Turbo and non Turbo..

Removal & Installation

Except Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release fuel system pressure.
  2. Remove the air cleaner lid, disconnect the inlet air temperature sensor and makeup air hose.
  3. Remove the negative battery cable.
  4. Remove the engine cover or throttle control shield if equipped.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  5. Disconnect fuel supply tube from rail.
  6. Remove the Intake Manifold, refer to the Engine section.
  7. Disconnect electrical connectors from fuel injectors.
  8. Remove bolts holding fuel rail.
  9. Remove the fuel rail and injectors.
  10. Remove the injectors from the fuel rail.
To install:
  1. Install injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  4. Attach electrical connectors to fuel injectors.
  5. Connect fuel supply tube to fuel rail. Refer to Quick Connect Fittings in the Fuel Delivery section
  6. Install Intake Manifold, refer to the Engine section.
  7. Install the engine cover or throttle control shield if equipped.
  8. Install the negative battery cable.
  9. Install the air cleaner lid, connect the inlet air temperature sensor and makeup air hose. Tighten air inlet tube clamps to 20-30 inch lbs. (2-4 Nm).

Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Disconnect the throttle body inlet hose and remove from throttle body.
  4. Disconnect the purge hose from the throttle body.
  5. Unlock and disconnect the electrical connection at the throttle body.
  6. Remove the throttle control shield .
  7. Remove the throttle and speed control cables from the throttle body.
  8. Remove the cables from the throttle body bracket.
  9. Unlock and disconnect the MAP sensor electrical connector.
  10. Remove the vacuum lines from the rear of the intake manifold.
  11. Remove the 5 bolts from the front of the intake manifold.
  12. Remove the 2 bolts from the rear of the intake manifold.
  13. Remove the intake manifold. Cover the lower intake manifold openings.
  14. Drain the Coolant system.
  15. Move the upper radiator hose clamp, so that the hose can be rotated up and out of the way.
  16. Remove the 2 small hoses from the thermostat housing.
  17. Remove the 2 bolts from the thermostat housing and rotate the assembly up and out of the way.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  18. Disconnect the fuel line from the fuel rail.
  19. Unlock and disconnect the electrical connectors from the fuel injectors.
  20. Remove the wiring harness from the fuel rail.
  21. Remove the 2 bolts from the fuel rail.
  22. Remove the fuel rail and injectors from the intake manifold.
To install:
  1. Install the fuel injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place.
  4. Install the 2 bolts to the fuel rail. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  5. Install the wiring harness to the fuel rail.
  6. Connect and lock the electrical connectors to the fuel injectors.
  7. Connect the fuel line to the fuel rail.
  8. Rotate the assembly back into place and install the 2 bolts to the thermostat housing tighten to 110 inch lbs. (12.5 Nm).
  9. Move the upper radiator house clamp back into place.
  10. Install the 2 small hoses to the thermostat housing.
  11. Fill the Coolant system.
  12. Install the intake manifold.
  13. Install the 2 bolts to the rear of the intake manifold tighten to 250 inch lbs. (28 Nm).
  14. Install the 5 bolts to the front of the intake manifold and tighten to 250 inch lbs. (28 Nm).
  15. Install the vacuum lines to the rear of the intake manifold.
  16. Connect and lock the MAP sensor electrical connector.
  17. Install the cables to the throttle body bracket.
  18. Install the throttle and speed control cables to the throttle body.
  19. Install the throttle control shield.
  20. Connect and lock the electrical connections at the throttle body.
  21. Connect the purge hose to the throttle body.
  22. Connect the throttle body inlet hose to the throttle body and tighten clamps to 20-30 inch lbs. (2-4 Nm).
  23. Connect the negative battery cable.
  24. Use the DRBĀ® scan tool ASD Fuel System Test to pressurize the fuel system. Check for leaks.

Mar 02, 2017 | Chrysler Cars & Trucks

1 Answer

How to replace the fuel injector on a 2008 chrysler pt cruiser


Removal & Installation

Except Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release fuel system pressure.
  2. Remove the air cleaner lid, disconnect the inlet air temperature sensor and makeup air hose.
  3. Remove the negative battery cable.
  4. Remove the engine cover or throttle control shield if equipped.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  5. Disconnect fuel supply tube from rail.
  6. Remove the Intake Manifold, refer to the Engine section.
  7. Disconnect electrical connectors from fuel injectors.
  8. Remove bolts holding fuel rail.
  9. Remove the fuel rail and injectors.
  10. Remove the injectors from the fuel rail.
To install:
  1. Install injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  4. Attach electrical connectors to fuel injectors.
  5. Connect fuel supply tube to fuel rail. Refer to Quick Connect Fittings in the Fuel Delivery section
  6. Install Intake Manifold, refer to the Engine section.
  7. Install the engine cover or throttle control shield if equipped.
  8. Install the negative battery cable.
  9. Install the air cleaner lid, connect the inlet air temperature sensor and makeup air hose. Tighten air inlet tube clamps to 20-30 inch lbs. (2-4 Nm).

Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Disconnect the throttle body inlet hose and remove from throttle body.
  4. Disconnect the purge hose from the throttle body.
  5. Unlock and disconnect the electrical connection at the throttle body.
  6. Remove the throttle control shield .
  7. Remove the throttle and speed control cables from the throttle body.
  8. Remove the cables from the throttle body bracket.
  9. Unlock and disconnect the MAP sensor electrical connector.
  10. Remove the vacuum lines from the rear of the intake manifold.
  11. Remove the 5 bolts from the front of the intake manifold.
  12. Remove the 2 bolts from the rear of the intake manifold.
  13. Remove the intake manifold. Cover the lower intake manifold openings.
  14. Drain the Coolant system.
  15. Move the upper radiator hose clamp, so that the hose can be rotated up and out of the way.
  16. Remove the 2 small hoses from the thermostat housing.
  17. Remove the 2 bolts from the thermostat housing and rotate the assembly up and out of the way.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  18. Disconnect the fuel line from the fuel rail.
  19. Unlock and disconnect the electrical connectors from the fuel injectors.
  20. Remove the wiring harness from the fuel rail.
  21. Remove the 2 bolts from the fuel rail.
  22. Remove the fuel rail and injectors from the intake manifold.
To install:
  1. Install the fuel injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place.
  4. Install the 2 bolts to the fuel rail. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  5. Install the wiring harness to the fuel rail.
  6. Connect and lock the electrical connectors to the fuel injectors.
  7. Connect the fuel line to the fuel rail.
  8. Rotate the assembly back into place and install the 2 bolts to the thermostat housing tighten to 110 inch lbs. (12.5 Nm).
  9. Move the upper radiator house clamp back into place.
  10. Install the 2 small hoses to the thermostat housing.
  11. Fill the Coolant system.
  12. Install the intake manifold.
  13. Install the 2 bolts to the rear of the intake manifold tighten to 250 inch lbs. (28 Nm).
  14. Install the 5 bolts to the front of the intake manifold and tighten to 250 inch lbs. (28 Nm).
  15. Install the vacuum lines to the rear of the intake manifold.
  16. Connect and lock the MAP sensor electrical connector.
  17. Install the cables to the throttle body bracket.
  18. Install the throttle and speed control cables to the throttle body.
  19. Install the throttle control shield.
  20. Connect and lock the electrical connections at the throttle body.
  21. Connect the purge hose to the throttle body.
  22. Connect the throttle body inlet hose to the throttle body and tighten clamps to 20-30 inch lbs. (2-4 Nm).
  23. Connect the negative battery cable.
  24. Use the DRBĀ® scan tool ASD Fuel System Test to pressurize the fuel system. Check for leaks.

Mar 02, 2017 | Chrysler Cars & Trucks

1 Answer

How do i replace fuel rail in 96 grand am 3100


disconnect the fuel lines at the fuel rail.then follow the fuel rail to disconnect every thing fastened to it,find the hold down bolts that fasten it to the motor(intake).unbolt the bolts.now you should blow any dirt around the areas were the fuel injectors go into the intake.disconnect the injector electrical plugs.pull the fuel rail and injectors together out of the car.you may need something to pry the rail/injectors up as it will be stuck to the intake.once out then you can remove the locking clips that hold the rail to the injectors and separate the injectors from the rail.install the injectors into the new rail in the same position as they were in the old rail.use a lubricant on the O rings when installing the injectors onto the new rail and insert the lock clips.lube the injector O rings on the end that goes into the intake and re-install in reverse order.reconnect items in reverse order and you can start the car.check for gas leaks.NOTE:if the O rings are cracked of broken replace with new injector O rings.

Apr 24, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

Fuel injector reeplacement


you don`t say what motor is in this so here is a basic procedure, find the fuel rail where the fuel lines connect to at the intake manifold.disconnect the fuel lines(be carefull you could get gas in your eyes from fuel spray or start a fire due to hot engine)these lines have high pressure fuel in them.look at the fuel rails to see what all is in the way to remove them and remove interferance items.remove the bolts that hold the rails to the intake manifold,gently lift wiggle the fuel rails and you may have to pry up on the rails in places to get them to come out with the injectors attached the rails.you should make sure any debris is removed from around the injectors so no dirt falls into the injector holes before you remove.then you can remove the injector to rail lock clips and remove the injectors from the rails.clean areas were the injectors will be going apply either gas or silicone on the injector O rings then install injectors to rail install lock clips and reassemble.replace all the O rings as they get dried out brittle and crack or split.re-install removed components start car and check for fuel leaks.

Mar 02, 2011 | 1998 Oldsmobile Silhouette

2 Answers

I need to replace the #2 fuel injector. Is this something a layman such as I can accomplish?


You could do it, but remember gasoline is flammable and volatile and can be hazardous to work with: REMOVAL AND INSTALLATION 1.9L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel rail
    • Fuel injector retaining clip off the injector
    • Fuel injector
    • Fuel injector O-rings and discard them Fig. 1: Fuel injector identification-1.9L engine 9306zg58.gif
    To install: NOTE: The SOHC and DOHC fuel injectors are not interchangeable. The injectors are identified by a color coded plastic ring near the bottom of the injector. The SOHC injector has a blue ring near the O-ring that mates to the intake manifold and the DOHC has a pink ring.
  4. Lubricate the new fuel injector O-ring with clean engine oil.
  5. Install or connect the following:
    • New O-ring seals on the fuel injector
    • Retaining clip to the fuel injector
    • Fuel injector to the fuel rail
    • Fuel rail
    • Negative battery cable
  6. Start the vehicle and check for leaks, repair if necessary.
2.2L and 3.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel rail
    • Fuel injector retaining clip off the injector
    • Fuel injector
    • Fuel injector O-rings and discard them
Fig. 2: Remove the retainer clip from the fuel injector - 2.2L and 3.0L engines 9306zg59.gif
To install:
  1. Lubricate the new fuel injector O-ring with clean engine oil.
  2. Install or connect the following:
    • New O-ring seals on the fuel injector
    • Retaining clip to the fuel injector
    • Fuel injector to the fuel rail
    • Fuel rail
    • Negative battery cable
  3. Start the vehicle and check for leaks, repair if necessary.
prev.gif next.gif

Feb 14, 2011 | 1999 Saturn SL

1 Answer

How to remove intake manifold on 2005 Buick Lesabre


You didn't post the size of your engine so please pick the appropriate one:

3.8L
  1. Relieve the fuel system pressure.
  2. Drain the cooling system.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Supercharger
    • Thermostat housing
    • Exhaust Gas Recirculation (EGR) tube at the intake manifold
    • Engine Control Temperature (ECT) sensor
    • Intake manifold
  • To install:

    1. Install or connect the following:
      • Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm).
      • ECT sensor connector
      • EGR tube to the intake manifold
      • Thermostat housing
      • Supercharger
      • Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.
    4.6L
    4.6L Engine
    1. Remove the brake booster hose from the throttle body.
    2. Remove the fuel pressure regulator vacuum tube from the fuel pressure regulator and the water crossover.
    3. Remove the PCV fresh air feed tube from the camshaft cover and the throttle body.
    4. Remove the PCV dirty air tube from the PCV orifice in the right camshaft cover and from the intake manifold.
    5. Disconnect the fuel injector electrical connectors from the fuel injectors.
    6. Remove the fuel injector wiring harness.
    7. Remove the fuel rail bracket nut from the engine lift bracket.
    8. Remove the fuel rail studs.
    9. Lift and remove the fuel rail with injectors.
    10. Loosen the plenum duct clamp in order to remove the intake manifold.
    11. Remove the intake manifold bolts.
    12. Remove the intake manifold.

    To install:

    1. Install the intake manifold, fitting the plenum duct over the intake manifold duct.
    2. Loosely install the intake manifold bolts.

    // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 45; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_21.gif

    Intake manifold torque sequence-4.6L engine


    1. Tighten the intake manifold bolts in sequence. Tighten the intake manifold bolts to 89 inch lbs. (10 Nm).
    2. Tighten the plenum duct clamp to the intake manifold. Tighten the plenum duct clamp to 24 inch lbs. (2.75 Nm).
    3. Inspect the fuel injector O-rings. Ensure the fuel injector O-rings are not missing, misaligned or damaged. Replace the O-rings if necessary.
    4. Lubricate the intake manifold fuel injector bores with light mineral oil (GM P/N 9981704), clean engine oil, or equivalent.
    5. Install the fuel rail with fuel injectors as an assembly.
    6. Install the fuel rail studs. Tighten the fuel rail studs to 80 inch lbs. (9 Nm).
    7. Install the fuel rail bracket nut to the engine lift bracket. Tighten the fuel rail bracket nut to 89 inch lbs. (10 Nm).
    8. Install the fuel injector wiring harness.
    9. Connect the fuel injector electrical connectors to the fuel injectors.
    10. Install the PCV dirty air tube to the PCV orifice in the right camshaft cover and to the intake manifold.
    11. Install the PCV fresh air feed tube to the camshaft cover and the water crossover.
    12. Install the fuel pressure regulator vacuum tube to the fuel pressure regulator and the throttle body.
    13. Install the brake booster hose to the throttle body.

    Nov 13, 2010 | Buick LeSabre Cars & Trucks

    1 Answer

    How to repair a supercharger


    Fig. 1: Supercharger assembly and related parts 84303024.gif

    REMOVAL & INSTALLATION
    1. Disconnect the negative battery cable.
    2. Remove the accessory drive belt from the supercharger pulley.
    3. Relieve the fuel pressure and remove the fuel injector sight shield.
    4. Disconnect the fuel pipes from the fuel rail and vacuum hose at the pressure regulator.
    5. Disconnect the electrical connectors from the fuel injectors and remove the fuel rail mounting bolts. Remove the fuel rail with the injectors intact.
    6. Disconnect the electrical connectors at the IAC, TPS, MAF, EGR and boost control solenoid. Lay the wiring harness aside.
    7. Remove the air intake duct and remove the EGR pipe from the supercharger.
    8. Disconnect the throttle cable and the cruise control cable. Remove the cable bracket.
    9. Remove the tensioner bracket to supercharger mounting stud.
    10. Remove the supercharger to intake manifold bolts, remove the supercharger from the intake manifold. Remove the supercharger gasket and coolant passage O-rings. To install:
    11. Replace the oil passage O-rings and the supercharger gasket.
    12. Install the supercharger and bolts. Install the tensioner bracket-to-supercharger bolt. Tighten the bolts to 19 ft. lbs. (26 Nm).
    13. Install the cable bracket and connect the throttle and cruise control cables.
    14. Connect the EGR pipe to the supercharger and install the air intake duct.
    15. Connect the electrical connectors to the IAC, TPS, MAF, EGR and boost control solenoid.
    16. Install the fuel rail and bolts and tighten the bolts to 15 ft. lbs. (24 Nm).
    17. Connect the connectors to the fuel injectors and the vacuum hoses at the pressure regulator.
    18. Connect the fuel pipes to the fuel rail and install the fuel injector sight shield.
    19. Install the accessory drive belt to the supercharger and connect the negative battery cable.

    Jul 14, 2010 | 1992 Buick Park Avenue

    1 Answer

    How do you install injectors in a chevy s-10 pick-up?


    Removal & Installation

    8205896.gif
    Exploded view of the fuel rail and injector mounting


    Take care when servicing the fuel rail assembly to prevent dirt or contaminants from entering the fuel system. ALL openings in the fuel lines and passages should be capped or plugged while disconnected.
    1. Before disassembly, clean the fuel rail assembly with a spray type cleaner such as AC Delco® X-30A, or equivalent. After removal, DO NOT immerse the fuel rail in liquid solvent.
    2. Properly relieve the fuel system pressure and disconnect the negative battery cable.
    3. Remove the air intake duct, as necessary for access.
    4. Tag and disengage the fuel injector electrical connectors.
    5. Disengage the fuel pressure regulator vacuum line, then tag and disengage all other necessary vacuum hoses.
    6. Loosen and remove the fuel rail retaining bolts.
    7. If necessary to remove the fuel rail assembly completely from the engine compartment, or to prevent stressing and damaging the fuel lines, disconnect the fuel lines from the rail assembly.
    8. Carefully lift the fuel rail assembly and fuel injectors from the intake.
    9. Carefully release and separate the fuel injectors from the rail assembly.
    10. Remove and discard ALL old O-rings from the fuel injectors and, if disconnected, the fuel lines.
    To install:
    1. Lightly coat the new O-rings with clean engine oil, then position them to the injectors and, if applicable, fuel fittings.
    2. Install the injectors to the fuel rail assembly.
    3. Carefully install the fuel rail and injectors to the intake manifold. Make sure the injectors are properly seated in their bores, but DO NOT force them into position.
    4. Install and tighten the rail retaining bolts to 62 inch lbs. (7 Nm).
    5. If removed, connect the fuel lines to the rail assembly and secure the fittings.
    6. Engage the fuel pressure regulator and any other vacuum lines, as noted during removal.
    7. Engage the injector electrical connectors.
    8. Connect the negative battery cable and cycle the ignition switch (without attempting to start the engine) in order to pressurize the fuel system, then check for leaks.
    9. Install the air intake duct.

    Apr 25, 2010 | 1992 Chevrolet S-10

    2 Answers

    After removing the fuel injectors and rail to remove the manifold, how do you reinstall the fuel injectors?


    the same way you took it apart. put a little grease around the rubber seals so they will slide in easier. just tap on the fuel rail while lightly tapping it into place.

    Mar 28, 2010 | 2002 Honda Passport

    1 Answer

    Engine compatible


    Yes. However it is a very expensive swap $5000 to $8000 to do it right. You will need the 1J or 2J engine, transmission, wiring harness, ecu, and alot of other pieces to do the swap. The engine brackets will need to be modified and you will have to upgrade your brakes. This kind of swap requires a good knowledge of the Toyota Supra and the engines. I do not recommend this swap for a beginner. A cheaper way is to take a 7M-GTE and upgrade the internals and turbo.

    Jul 09, 2009 | 1987 Toyota Supra

    Not finding what you are looking for?
    1994 Toyota Supra Logo

    Related Topics:

    232 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75066 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7754 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...