Question about 2008 GMC Sierra 2500HD 2WD

Open Question

How do you replace carrier bearing on a gmc sierra 2500 hd

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 375 Answers

SOURCE: 2007 gmc sierra 2500 IAT sensor

Well, the IAT (Intake Air Temperature) sensor is located on the air intake duct between the filter and the throttle body (Assuming you have the 6L motor). The wires are easily visible at the plug that connects the sensor to the wiring harness. That's the easiest place to access them.

Posted on May 18, 2008

Molson02536
  • 3854 Answers

SOURCE: how to adjust parking brake on a GMC Sierra 2500

The adjuster is just like on a car with drum brakes. It can be adjusted with the wheels still on the truck, but if yours is out enough that it doesn't work, an inspection is warranted. Axle seal failure is common and will soak the shoes.

Jacked both rear wheels off ground, and while slowly spinning wheel, tighten the star-wheel adjuster until you just hear and feel brake drums rubbing, then loosened slightly.
There's a plastic dust cover about 1/4" X 1" that you remove, and use a drum brake adjuster tool.

The driverside access hole is below axle, easily accessable. To tighten driver side rear parking brake, turn star-wheel adjuster down.


The passengerside access hole is found above axle, and difficult to see. Removed pass side wheel and used an inspection mirror.
To tighten passenger side rear parking brake, turn star-wheel adjuster up.

Good luck and hope this helps. Oh and the other thing to is that if you do smell axle fluid around the wheels and see oil leaking from the drum area. Then you have a axle wheel seal and or bearing gone bad too.

Posted on Apr 13, 2009

  • 462 Answers

SOURCE: I need to replace the fuel filter on my 2003 GMC

ITS A SPIN ON FILTER, YOU NEED TO DISCONNECT THE WATER SENSOR ON THE BOTTOM OF THE FILTER, THEN USING A STRAP FILTER WRENCH LOOSEN THE FILTER AND SPIN IT OFF.

CHECK THE FILTER HOUSING TO BE SURE THE INNER FILTER SEAL ISN'T ON THE HOUSING AND CAME OFF WITH THE FILTER.

REMOVE THE WATER LEVEL SENSOR AND DISCARD THE SEAL.

INSTALL THE WATER LEVEL SENSOR ON THE NEW FILTER. USING A LITTLE GREASE ON THE INNER FILTER SEAL AND ON THE OUTER O-RING TO HOLD IT IN PLACE, SPIN ON THE NEW FILTER.

OPEN THE VENT ON THE UPPER SIDE OF THE FILTER HOUSING. PUSH DOWN ON THE HAND PUMP QUICKLY UNTIL THE FUEL IS COMING OUT OF THE VENT. CLOSE THE VENT AND PUMP THE FILTER PUMP UNTIL IT FEELS SOLID. AT THIS POINT START THE ENGINE. IF IT STALLS PUMP IT UP AGAIN AND RESTART THE ENGINE. IF YOU HAVE AN ASSISTANT THEY CAN PUMP THE FILTER PUMP WHILE THE ENGINE IS RUNNING AND QUIT WHEN YOU FEEL THE ENGINE IS NOT GOING TO STALL. ABOUT 10 TO 15 SECONDS USUALLY WORKS.

CHECK FOR LEAKS.

BEFORE STARTING THE ENGINE USE BRAKE WASH TO REMOVE THE FUEL SPILLED DURING THE FILTER REPLACEMENT. ALLOW IT TO DRY BEFORE STARTING THE ENGINE.

RATE ME PLEASE.

Posted on Jul 07, 2009

  • 1 Answer

SOURCE: how to replace starter 2002 GMC Sierra 2500

Enjoy this...jack up truck, remove tire, remove plastic cowling and expose front right wheel well.you may want to wash this side of engine at this point. Remove battery cables, remove the 13 mm nut and 8mm nuts on the solenoid. take a 15mm socket and remove the upper aand lower holding bolts. Use an extra long extension for the lower bolt. Ratchet out in front of the A-arm. Dislocate the starter from the fly wheel side of starter. wiggle,jiggle and point the starter gear at a 45 down and PULL starter out and down.

Posted on Mar 29, 2010

  • 4336 Answers

SOURCE: how do you reset a

Check engine light will go out when the management computer detects no more errors. Pull the codes and repair what they indicate.

Posted on Sep 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How hard is it gonna be to get to the passenger side freeze plug on my 2002 gmc Sierra 2500 hd


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Dec 20, 2016 | 2002 GMC Sierra 2500

1 Answer

Penion shaft seal and bearing removal and repair


You need a heavy press to replace the bearing so they can be done at home. Remove the carrier from the banjo housing and have a machine shop replace the pinion bearings and carriers bearings

Jul 15, 2012 | 1999 GMC Sierra

1 Answer

2005 GMC 4x4 HD 2500 6.0 eng. rear axel seal


SEAL COULD BE LEAKING CAUSE YOU DIDNT LUBRICATE THE SEAL LIPS WITH PETROLEUM JELLY TO HELP THE THE SEAL LIP SEAL OR YOU DAMAGE THE SEAL WHILE DRIVING IT IN.AXLE FLANGE NUTS TORQUE IS 58 FT LBS THE AXLE HUB NUT TORQUE IS 177 FT LBS.

Jul 14, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

2004 GMC Sierra 2500 HD. Drivers side mirror was


You should be able to replace the glass, but I believe it is glued in place. You should be able to tell as you remove the old pieces. It is a special white glue.
I was able to get a great price for the whole mirror on ebay. even the ones with signals and heated.

Hope this helps

Jan 09, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

Gmc Sierra Tailgate wont shut


Check with a Body Shop Technician for the proper description.

Jun 15, 2009 | 2004 GMC Sierra 2500

5 Answers

2003 gmc sierra duramax 2500


Problem with Diesel Fuel System. Gmc 2002 duramax 2500 HD 4x4 will start 

Apr 19, 2009 | 2003 GMC Sierra

1 Answer

2003 gmc 2500 hd turn key nothing happends


try checking your neutral safety switch.

Apr 15, 2009 | 2003 GMC Sierra 2500HD

1 Answer

Mass air sensor and intake air temperature sensor


They are not the same thing but the air temp sensor is made into the mass air sensor

Nov 20, 2008 | 2004 GMC Sierra 2500

1 Answer

Fan only works on high 02 gmc hd 2500


There is a resistor attached to the blower box. Replace the blower resistor and this should solve your problem

Sep 16, 2008 | 2002 GMC Sierra 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

577 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...