Question about 1996 Chrysler Cirrus

Open Question

Headlights not working

My headlights only work when I put the brights on,how do I replace bulbs,looks like a major deal.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
demonsm
  • 253 Answers

SOURCE: headlights don't work, low or high beam-

Light switch bad or check all head lightrelays . 2 dim ones and 2 high beam ones. one is bad.

Posted on Mar 15, 2009

Ad
  • 1810 Answers

SOURCE: 91 chrysler newyorker

sounds like a reley
change the high low releys arround
also look to see if you have 2 different flip releys

Posted on Aug 03, 2009

  • 1986 Answers

SOURCE: Adjust the headlights on 2005 Sebring, Touring Sedan

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall. Also mark where the center of the bulbs would be (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall. For horizontal, aim the hot spot directly at the line you marked for the center of your bulbs

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

  • 1 Answer

SOURCE: head lights won't turn on. check bulbs and they

I have the exact same problem. my high beams work but my low beams do not. a solution would be great!

Posted on Nov 10, 2009

fridakha2
  • 35 Answers

SOURCE: where are the fuses for the headlights

MOST CARS WILL BE INSIDE THE DRIVER SIDE LOOK FOR A LITTLE DOOR AND ONCE YOU OPEN IT IT WILL GUIDE YOU TO THE RIGHT FUSE . FOR GERMAN CARS IT MAY BE ON PASSENGER SIDE UNDERNEATH THE GLOVE BOX TO THE RIGHT

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 sentra headlights


Check fuses with a test light Rob, in the power dist center under the hood, Check the lid for fuses to each headlight , high beam and low. Next check for current at the connector after you remove one of the low beam headlights.

Feb 03, 2014 | Cars & Trucks

1 Answer

Headlights wont work on dim, only bright


Check your head light bulbs, your truck has the dual filiment headlight bulbs one per side which does both high beam and low beam, 9007 bulbs.
If the low beam filiments are burned out only the high beam will work.
Also look into finding out if the headlight switch is gone bad.
The headlight module and or drl module maybe defective.

Jan 24, 2014 | 1996 Ford Ranger SuperCab

1 Answer

Both dim headlights will not burn. brights work just fine. checked fuse and switched relays with no result. any other ideas??


Most headlights have two different bulbs: one for regular/dim and one for bright. It's time to replace your headlights.

Oct 27, 2012 | 2006 Chevrolet Trailblazer

1 Answer

Both headlights stopped working. Need to turn on


You probably have a bad switch.If your hi beams work then the fuse is good.

Jan 07, 2010 | 1992 Oldsmobile Ninety Eight

1 Answer

My headlights work on brights but wont work on


might have to replace the headlights/bulbs. I have an 85 rx7 and I didnt have low beams only high and I replaced both headlights and now they work.

Oct 19, 2009 | 1994 Mazda RX-7

1 Answer

Headlights not coming on CJ7


Test and replace the bulbs.

May 01, 2009 | Jeep CJ7 Cars & Trucks

2 Answers

1998 ford ranger headlights do not come on when switch is turned


Look under the hood.
There is a large relay which should have some info about lights on it.
I had this exact problem with my dodge ram

Jan 26, 2009 | 1998 Ford Ranger SuperCab

2 Answers

1996 ford ranger headlights not working


It's the dimmer switch in the column.

Jan 06, 2009 | 1996 Ford Ranger SuperCab

4 Answers

When i put my brights on my headlights go out


Replace your headlights. Your brights are no longer working. There are 2 sets of lights in each headlight. One set for your dims and one set for your brights. It is time to replace the lights.

Dec 05, 2008 | 1998 Pontiac Grand Am

2 Answers

Headlights Not Working, Brights and Turn Signals Work


This is cuased by the multifuntion switch that is located on the steering column. It is the swith with the headlight dimmers on it.

You just need to remove the steering column bezels and replace the multifunction switch.

Aug 29, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
1996 Chrysler Cirrus Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...