Question about 2002 Kia Sedona

Open Question

How to remove rear wheel bearings on 2006 Kia Sedona

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 334 Answers

SOURCE: wheel bearings

the wheel bearin and hub is one . the bearin is press in . some times it just easer to change the hole thing .and you will have to disconect the tierod upper and lower ball joint . i hope this help you

Posted on Apr 05, 2009

  • 4369 Answers

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Posted on Apr 10, 2009

Healeyman
  • 1198 Answers

SOURCE: front wheel bearing removal on 2006 F350 touchtone 4X4

Get a good repair manual. Front ends on 4X4s require proper care.

Posted on Apr 25, 2009

  • 1 Answer

SOURCE: Rear Brakes drum 2004 Kia Rio

The rear drums are held on by a spindle nut. You first must remove the dust cap then unstake the nut and remove it. Behind that is a retaining washer and the outer bearing. The bearings can become a little stuck in which case a hammer can usually persuade them to loosen up.

Posted on May 29, 2009

techbuster
  • 5081 Answers

SOURCE: how do i remove the rear brake drum from a kia

You need to back off the adjuster located at the top the brake assembly.There's an rubber grommet on the backing plate.You need to use a short flat screwdriver and ratchet back the star wheel in which you acess through the small hole in the backing plate.Now there's an arm that rests on the notches of the star wheel of the adjuster so the brakes don't back off, as the going down the road.This needs to be pushed away from the star wheel in for you to back off the adjuster.This will contract the brake shoes away from the drum.This will allow you to remove the drum.


**A word of caution: if you don't move that arm, You'll be able to adjust the star wheel!but your now expanding the shoes closer to the drums! If it doesn't have automatic adjusting brakes so,you'll have to expand the shoes one click every 7000 miles or click it then spin the drum,continue to adust until you feel an slight drag on the drum as you spin it!

Posted on Oct 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Kia Sadona, rear wheel studs, how to get off. Emergency brake assay seems to be In the way. He'll me please


You can remove studs with sharp nosed pliers, but it is not easy to do....lots of work.

Jan 10, 2017 | 2006 Kia Sedona

1 Answer

Is there a trick to installing the bearing front end KIA sportage


Fix It Right! - Front Hub Bearing Replacement - YouTube

? 14:26
https://www.youtube.com/watch?v=l0LCkycUcqM
Sep 7, 2011 - Uploaded by OneSourceAutomotive
Front Hub Bearing Replacement (S1E3) Demonstrated on a 2004Kia Sedona FWD. ... on a front-wheel ...

Kia Sportage wheel bearing replacement - YouTube

? 4:10
https://www.youtube.com/watch?v=wa6NREeozbE
Apr 3, 2014 - Uploaded by Jo Daddy's Garage
I did a quick replacement of a bad rear wheel bearing/hub on aKia ... How to install front struts on a Kia ...

Dec 09, 2015 | Kia Cars & Trucks

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

Removing 2006 kia sedona captain seats


Ditto for me. My son accidently latched one of the rear latches but none of the others. We could not get it off. We found this answer and tried it and it worked. I lifted on the rear of the seat while he folded the back of the seat down. It released when we did this. Whew

May 17, 2012 | 2006 Kia Sedona

2 Answers

Rattle in rear


I've had both rear wheel bearings go on my 2003 Sedona. Both made this same rattling sound. It's about a $300 job.

Jun 27, 2010 | 2003 Kia Sedona

1 Answer

R & R pass front wheel bearing on 2005 Kia Sedona-how?


have you got a press to remove bearing

Apr 10, 2010 | 2003 Kia Sedona

1 Answer

Wheel bearings need replaced, what is the cost?


bearing about £50 plus about 2hrs labour

Feb 11, 2010 | 2002 Kia Sedona

Not finding what you are looking for?
2002 Kia Sedona Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...