Question about 1995 Jeep Cherokee

1 Answer

What is the procedure for adding Freeze 12 to the compressor?

Posted by on

  • Richard Scordino May 11, 2010

    I'd suggest having a good shop do that for you. It is easy to do it the wrong way, and takes a trained tech to do it correctly.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Review the XJ Service Repair Manual Section 24 Heating & Air Conditioning - 95XJ_24 (page 11 and next).

I hope help you (remember rated this help) Good luck.

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many cans of refrigerant for a 1994 Ford F150? I've added one large can, but only air down to 84' The compressor came on while I was filling it for 5-6 seconds. on and off


U fill the unit until the suction line of unit by compressor sweats and beads but does not freeze up. If you over fill you will not get the correct cooling since flashing will take place in the suction line instead of the evaporator.

Jun 15, 2017 | Ford Cars & Trucks

1 Answer

98 expedition with dual air. pressures were 50 and 225 at idle at 90 - 95 deg outside. Compressor cycled and air got warm when driving. Added 12 OZ of freon. pressures went 60 and 250. added another can...


sounds like the expansion valve or the orfice may be clogged is your compressor making noise like a clinging inside if it isyou'l need to change the accumlator dryer as well as expansion or orfice along with the compressor. you could try what are the pressures with a fan in front of the vehicle if they go to 35-40 psi on low side and 200-250 psi on high side these are close to where they should be.

Jul 07, 2012 | 1998 Ford Expedition

1 Answer

How to install a 1999 yukon ac compressor


Hi.

Follow below...

jshreader_20.jpg

REMOVAL PROCEDURE

CAUTION: Refer to Battery Disconnect Caution in Cautions and Notices.

1. Disconnect the negative battery cable.
2. Recover the refrigerant.
3. Remove the drive belt.
4. Disconnect the refrigerant hose assembly from the compressor.
5. Cap or plug all of the open connections.
6. Disconnect the electrical connectors, as necessary.
7. Remove the bolts.
8. Remove the compressor from the bracket.
9. Drain the compressor oil.
10. Measure the compressor oil. Refer to Adding Oil .

INSTALLATION PROCEDURE

1. Fill the compressor with oil. Refer to Adding Oil .
2. Install the compressor to the bracket.

NOTE : Refer to Fastener Notice in Cautions and Notices.

3. Install the compressor mounting bolts.

Tighten
Tighten the bolts to 50 N.m (37 lb ft) .

4. Connect the electrical connectors, as necessary.
5. Install the refrigerant hose assembly to the compressor.
6. Install the drive belt.
7. Connect the negative battery cable.
8. Charge the system. Refer to Refrigerant Recovery and Recycling, Adding Oil, Evacuating and Recharging Procedures .
9. Inspect the system for leaks.

I hope this helps.

Thanks...

Dec 03, 2010 | 1999 GMC Yukon

2 Answers

Were di i recharge the ac on my car


if it is the 3.4 v6 the low side is on the passager side behind the motor. it should have a blue cap on it, and the low side is the fatter of the two ac lines

Aug 08, 2010 | 1994 Pontiac Grand Am

2 Answers

Air conditioner compressor making a knocking noise while running.i read that oil needs to be put in it if so where and how or do I need to plan on replacing the compressor


Get a can of R134a refrigerant with sealant and oil and add with a hose.
Can buy at Walmart for under $30.
Buy the conversion from R-12 to R134a kit if you need to.

Sometimes adding a few ounces of oil will quiet the compressor but you have to try.

Compressor is probably a few hundred dollars to replace, so try the cheap solution first.

Jul 04, 2010 | Cars & Trucks

2 Answers

On my 2003 Chevy Silverado, the A/C compressor won't kick on. Just blows out warm/hot air.


The ac system may need freon added,if the system is low,or out of freon,it will not allow the ac compressor to come on.

Apr 11, 2010 | 2003 Chevrolet Silverado 2500HD

2 Answers

Air conditioner is blowing hot air out what should i add


On a 92 you might still have the old refrigant that you cannot mix with R134A. You will need to adapt the system the new R134A (gaskets etc....). Does the compressor come on?

Aug 17, 2009 | 1992 Saturn SL2

1 Answer

I need to replace the alternator on my sisters car and its not here right now and was wondering where the alternator is located so i will know if ill be able to get to it to fix it


if you have the 2.3 liter engine follow these steps...
  1. On models with anti-theft audio system , refer to Technician Safety Information .
  2. Disconnect battery ground cable.
  3. Remove lefthand charge air cooler, then righthand upper seal board, Fig. 3 .
  4. Remove condenser fan assembly.
  5. Disconnect alternator, then alternator electrical connector.
  6. Remove lefthand splash shield.
  7. Remove drive belt.
  8. Remove A/C compressor, then, with pipe still connected, position A/C compressor away from generator for easy access to alternator.
  9. Remove alternator from under vehicle.
  10. Reverse procedure to install, noting the following:
    1. Torque lefthand splash shield bolts to 70 - 95 in.lb.
    2. Torque condenser fan bolts to 70 - 95 in.lb.
    3. Torque lefthand charge air cooler nuts to 12 - 16 ft.lb.
if you have the 2.5 liter engine then follow these steps....
  1. On models with anti-theft audio system , refer to Technician Safety Information for system deactivation procedure.
  2. Disconnect battery ground cable, then remove electrical harness, Fig. 4 .
  3. Disconnect terminal B wire, then alternator electrical connector.
  4. Remove righthand splash shield.
  5. Remove drive belt.
  6. Remove A/C compressor; then, with pipe still connected, position A/C compressor away from generator for easy access to alternator.
  7. Remove alternator from under vehicle.
  8. Reverse procedure to install, noting the following:
    1. Torque upper alternator bolt to 12 - 16 ft.lb., then lower alternator bolt to 24 - 33 ft.lb., Fig. 4 .
    2. Torque A/C compressor bolts to 12 - 16 ft.lb.
    3. Torque righthand splash shield bolts to 70 - 95 in.lb.

Aug 04, 2009 | 1995 Mazda Millenia

1 Answer

Ac problem


Static pressure(Non operating) usually is around 70 lbs and should be even on both sides. Sounds like the systen is too low for the computer to allow operation. I suspect a small leak somewhere. Adding as little as 1/2 lb should allow operation and leak testing.

Jun 19, 2009 | 2000 Chevrolet S-10

1 Answer

Air compressor


actually might be not to hard, the problem is than you need a recovery machine to save the refrigerant and then recharge the system with refrigerant, and acording to the year of your car it might be R-12 OR R-134. REFRIGERANT, if r-134 it is ok but if it has R-12 then just have a shop working on it since the r-12 is too expensive, i will recomend you to retrofit the system tro freeze-12 all this 12s and 134s than i'm talking about is the kind of refrigerant on your car, but if it has r-134 leave it like that,
and feel fre to ask for any thing elese and good luck
just one more thing, if you are going to try to recharge the system by your self make sure to do it by the low pressure side and not the high because it will be very very dangerous.

Jun 16, 2008 | 1995 Pontiac Grand Am

Not finding what you are looking for?
1995 Jeep Cherokee Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...