Question about 1995 Ford Taurus

1 Answer

Finding access to front corner lamp base location to

Finding access to lamp base on right front corner lamp location to replace 194NA bulb on a 1995 Ford Taurus

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,077 Answers

U do this from under the car between the fender and the wheel well liner

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fit a new headlight bulb on 1995 jeep cherokee


Check this details, from the Repair Manual...
2_27_2013_8_57_15_pm.jpg


HEADLAMP BULB REMOVAL
(1) Lift hood to access lamps.
(2) Reach into engine compartment and locate lock ring supporting the headlamp bulb assembly.
(3) Rotate the lock ring 1/8 turn counterclockwise (Fig. 5).
(4) Pull the bulb (9004) straight out from the housing. This is a halogen bulb, take care not to touch it with your fingers.
(5) Replace by seating the assembly in the lamp housing and turning the lock ring 1/8 turn clockwise to secure.

Hope this helps.

Feb 27, 2013 | 1995 Jeep Grand Cherokee

1 Answer

How do i remove lamp to replace it? Thank you


Hello there,
Please follow the steps below to be able to replace the lamp,
  1. Park the vehicle on a level surface. Turn off the engine.
  2. Remove the four pushpins located on the underside of the protective shield on the front of the vehicle. Remove the protective shield from the vehicle.
  3. Reach behind the front bumper area from under the vehicle to access the lamp housing.
  4. Remove the largest bulb socket from the housing by rotating the socket counterclockwise. Disconnect the electrical connector from the bulb by lifting the two plastic clips at the base of the bulb.
  5. Pull the burned-out bulb out. Replace it with a new bulb by pushing the new bulb directly into the socket. Reconnect the electrical connector to the socket. Place the socket back into the housing. Rotate it clockwise to secure it in place.
  6. Reattach the protective shield to the front of the vehicle by reinstalling the pushpins.
Hope this helped. Goodluck Elect_Comp

Aug 30, 2011 | Cadillac STS Cars & Trucks

1 Answer

How do replace driver side headlight bulb? What size do I get?


Go to your local auto parts store.Ask at the counter,give them your make and model and year.

High & Low Beam Headlamp Light Bulb Size: 9007
Parking Light Bulb Size: 194NA
Front Turn Signal Light Bulb Size: 7507 Or 2827
Rear Turn Signal Light Bulb Size: 7507
Tail Light Bulb Size: 7443
Stop Light Bulb Size: 7443
High Mount Stop Light Bulb Size: 7506
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 921
Front Side Marker Light Bulb Size: 194NA
Rear Sidemarker Light Bulb Size: 7443
Dome Light Bulb Size: DE3175
Trunk/Cargo Area Light Bulb Size: DE3022

The bulb is in a socket which will twist out,then there may be a clip that holds the bulb in.

Jun 25, 2011 | 2003 Mitsubishi Lancer

1 Answer

1995 LeSabre- right blinker doesnt blink, I have to manually blink the signal. The light bulb on the front side marker doesnt light up, but the front one does. Do I replace that little side bulb, 194na?...


Hi, The bulbs that you take out should be the same that you put in. (volts and color) If blinker is going faster in one derection this is an indecation tha the bulb is no good any more. Replace it with same type. Good luck.

Jun 21, 2011 | 1995 Buick LeSabre

2 Answers

What is the part number for a replacement bulb for a 1997 Jeep Grand Cherokee front turn signal? Front, not side!


The part # for your 1997 grand cherokee front turn signal bulb not the side is 3057, good day

Apr 14, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I need to replace a foglamp bulb right side.I have fairly easy access to & can see the rubber housing for the bulb,but cannot figure out how to remove it.Do I need to rermove the entire assembly in...


Typically the fog lamp is located in the front bumper assembly. It's usually fairly easy to access and replace these.

Place the car is park, secure parking brake. Use a creeper to scoot under the front end of the car, look up into the bumper. Located the backside of the fog lamp holder. You would usually grab and twist counter clockwise about an inch, then pull straight out. Push in on the bulb while turning counter clockwise until it pulls out of the lamp holder.

These fog lamps usually have a little bit of cushioning grease in the socket. Do not remove the grease or connectivity problems will result with the new fog lamp. Push the new bulb in, turn clockwise until bulb stops turning, release hand pressure.

Installation is the reverse of removal.

May 25, 2010 | 1999 Oldsmobile Eighty Eight

1 Answer

Replacing headlight


Composite Headlights
Most of the vehicles covered by this manual are equipped with composite headlight assemblies. Due to space constraints, no access may be provided to withdraw the bulbs, so the replacement usually requires removal of the composite assembly.

CAUTION The composite headlight assemblies use Halogen bulbs which contain a gas under pressure. Improper handling of the bulb could cause it to shatter into flying glass fragments. To help avoid personal injury, follow the precautions closely.



e5415df.gif
Exploded view of the composite headlight mounting—1995-97 model shown

Whenever handling a Halogen bulb, ALWAYS follow these precautions:
  • Turn the headlight switch OFF and allow the bulb to cool before changing it. Leave the switch OFF until the change is complete.
  • ALWAYS wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • DO NOT drop or scratch the bulb.
  • Keep dirt and moisture off the bulb.
  • Place the used bulb in the new bulb's carton and dispose of it properly.
  1. Raise the hood and locate the bulb mounting location at the rear of the composite headlamp body.
  2. Disconnect the negative battery cable.
  3. If necessary for access, remove the splash shield or side marker lamp(s).
  4. On some models it may be necessary to remove the side marker lamp.
500cb2e.gif
Unfasten the thumb screws, then ...

  1. If there is enough room to access the plastic base, press in and turn the base 1/4 turn counterclockwise and remove from the metal retaining ring by gently pulling back and away from the headlight. Remove the electrical connector from the bulb by raising the lock tab and pulling the connector down and away from the bulb's plastic base.
  2. If you can't access the bulb from the engine compartment, unfasten the thumb screws, and/or other retainers, then pull the composite headlight assembly forward slightly and disengage the wiring connector. Press in and turn the base 1/4 turn counterclockwise and remove the bulb from the metal retaining ring by gently pulling back and away from the headlight.
6f66f0b.gif
... pull the headlight assembly away from the vehicle for access to the bulb and connector

8b6245d.gif \
Remove the retaining ring from the base of the bulb, then ...

e28b933.gif
... turn the bulb and remove it from the headlight assembly

To install:
  1. Attach the electrical connector on the new bulb's plastic base making sure that the lock tab is in place.
  2. Install the bulb by inserting the smallest tab located on top of the plastic base into the corresponding notch in the metal retaining ring. Turn clockwise 1/4 turn until it stops. The small plastic tab should be at the top of the metal ring.
  3. Install the composite headlight assembly, then secure with the retainers.
  4. Connect the negative battery cable, then check for proper headlight operation.

Jan 10, 2010 | 1997 Buick Skylark

1 Answer

Trying to change the front passenger turn light


Cornering Lamp Removal & Installation To Remove:
  1. Remove the bulb socket from the cornering lamp.
  2. Release the cornering lamp forward retaining tab and pull the front of the lamp away from the fascia.
  3. Remove the cornering lamp rearward retaining stem from the fascia by pulling the lamp forward.
To Install:
  1. Place the cornering lamp rearward retaining stem into the slot in the fascia.
  2. Engage the cornering lamp forward retaining tab into the fascia by pushing in on the front of the lamp.
  3. Install the bulb socket into the cornering lamp.

Jul 10, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

How do I remove the cover on a 2002 325i BMW tail light wiring? thanks


Do you need to change a bulb or are you changing to custom lamps. If it is bulb replacement open trunk/boot (depending where you live ) the access for the tail lamps is at the rear corners of the trunk, If you are changing lamp lenses or assembly remove the screws( same location ) at lamp corners

Jul 09, 2009 | 2001 BMW 325

1 Answer

Signal light bulb change/who and where


  1. From under front wheelhouse, remove access cover behind park and turn signal lamp
  2. Through access hole in wheelhouse, rotate park and turn signal socket counterclockwise one quarter turn.
    1. Pull socket from back of lamp.
    2. Pull bulb from socket. INSTALLATION
      1. Align key on bulb base to groove in socket and insert bulb into socket.
      2. Through access hole in wheelhouse, insert socket into back of lamp.
      3. Rotate park and turn signal socket clockwise one quarter turn.
      4. Install access cover and verify lamp operation.
Hope this helps with your prob

Mar 27, 2009 | 1998 Plymouth Voyager

Not finding what you are looking for?
1995 Ford Taurus Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...