Question about 1994 Mitsubishi Eclipse

1 Answer

My rear passenger inner brake pad is wearing at an angle and not the outer one whats the deal?

Posted by on

  • Christopher Foulkes May 11, 2010

    Have you checked the caliper slides and if the brake pads slide easily in the pad holder? If either one is frozen it can cause the pads to wear uneven.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 69 Answers

You probably will have to free off the pistons in the caliper. Sounds like the outer one is ceased. A G-clamp is good for this

Posted on Oct 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear brakes dragging


Normally I would say check the brake hose, but that would only be for one wheel.
If the rear brakes are not releasing normally, either something is keeping pressure applied, or the calipers are not sliding back. If both inner and outer pads are wearing down equally on both wheels, I would look for a pressure problem. If only the outboard pads are wearing, the calipers are sticking in place.

Jun 28, 2013 | Cars & Trucks

1 Answer

How can i compress the caliper piston back of audi a6 2000 2.8l awd what kind of tools i need . Vise grip is not working.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!

For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!

Check brake fluid level and top up if neccessary!!!

Oct 26, 2011 | 2000 Audi A6

1 Answer

What size bolt holds the brake and caliper on a 99 Volkswagon Passat


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Mar 27, 2011 | 1999 Volkswagen Passat

1 Answer

My 2006 mercedes e500 brakes are squeaking when I brake. Does this mean I have to replace the brakes?


first check brake pads, are they in good condition first remove front pads and grind outer edge and inner edge 1 mm with angle from mettle part, do the same for both pads in each wheels then fix it back, do the same to the rear pads too, the problem is your brake rotors are wear, when you replace brake pads next time must need to be replace brake rotors together with the pads. is this information helped you?

Oct 27, 2010 | 2006 Mercedes-Benz E-Class

1 Answer

I have a 1988 camry that the inner brake pad is worn completely out but the outer has hardly any wear. Any suggestions?


Hi,
You may want to clean the bolts that the caliper slides on and use some silicone lubricant on those bolts. The caliper needs to slide back and forth to use both the inner and outer pads. Sounds like the caliper piston is pushing the inner pad but the caliper is hanging up so as not to engage the outer pad.
Good Luck,
Wayne

Oct 19, 2010 | 1988 Toyota Camry

1 Answer

WHAT TOOLS ARE NEEDE TO REPLACE AUDI A3 SPORTSBACK FRONT BRAKE PADS


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. You must buy the brake pads with wear sensor. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exists, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Feb 14, 2010 | 2006 Audi A3

1 Answer

Ok when i am driving my car and when i need to apply the breaks they make a almost squealing noise but after i drive for a little the stop any help will be much appriciated


I have same problem; turns out all Honda Accords of this generation (2003-2007) do this. It has something to do with cold brakes and unseated pads, and the first time you stop from medium speed, you will hear a grinding, maybe from the back of the car (i think in my case).
My girlfriend looks at me, and we both wonder what it is, but it goes away in about 1 minute and I've realized it's only when the brakes are cold and it's not a problem. My brakes are basically ok, and there is nothing to fix...
I've done enough reading about this car on the internet, I feel pretty sure everybody's Accord does this, so I stopped worrying about it. A real problem, the sound would not go away as soon as the brakes warm up and seat the pads. After that, the breaks work fine.
If it was worn pads, the squealers will start up and not go away quickly. If it was a worse problem, the sound would grind continuously until fixed.
The two major problems with Honda Accord brakes are: 1) Brake judder at hi-speed medium braking. If you are going downhill, and just want to slow the car a little, if your rotors are getting worn, the steering wheel will give you feedback as brake judder. Hit the brakes harder, it will go away but it's scary and requires the rotors be replaced with a much higher quality rotor than came from the factory, and probably want to use ceramic pads (like Bendix CQ or CT). 2) Back brake pads wear down quickly. I read about this constantly with Accord owners, the EX back brakes are smaller rotors and pads than the front, but the electronic brake distribution system of the Accord will balance brake force between front and back, so the front pads will actually last longer than the back pads! This is very unusual but entirely normal for this car. Most cars are the opposite but that may change as we see new generations of cars with more evenly balanced braking front to rear. Be ready and watch your back brakes closely. Mine were toast at 30k...
I replaced my back pads and rotors, used cheapest new rotors I could find, and ceramic pads, and they have lasted considerably longer than the first set.
I now have 92k on my 2004 and the original front brakes are ready to be replaced. I replaced back brakes at 34k I think, and was very surprised they needed replacement at early, but the new pads have gone almost 60k, but look ready to be replaced sometime this year I think.
I have bad judder on high speed braking, but the pads are still ok in front. Rotors are **** in front and I'll replace with Centric Cryo-Stop rotors, they should last a long time as long as they get put on straight and I don't let anybody warp them with an air gun at the tire shop...
Two other more minor problems to watch for on this car: 3) Inner pads may wear faster than outer pads, because the caliper is on the inside, and forces the outside pads to contact the rotor after the inner pads are already braking. Seems like all Accords do this at least a little. The inner pads are not easily viewed without removing wheels, so it's hard to tell, but if your outer pads look like they are starting to get worn down pretty well, chances are good the inner pads are even more worn and you are ready to replace pads. 4) Pads may wear faster on one side of the car (fronts) faster than the other side. For example many people report driver side pads wear faster than passenger side. And the reasons proposed have to do with fast stopping for right hand turns or freeway loops. The car spends more time being braked in a right turn than a left over time.. But of course, on my car, it seems to be the opposite. The passenger side is wearing faster! Go figure..

Jan 12, 2010 | Honda Accord Cars & Trucks

1 Answer

Thickness of brake disks for Suzuki Ignis Sport 109 HP, 2004


Generally you do not want to let them wear anymore than 1/16 of an inch either inner or outer pad. The inner pad will wear a little faster than the outer, but you will want to go by which ever one is thinner. As far as the parameters of new disk, they will have a minimum thickness per DOT standards. The minimum thickness is usually stamped on the disk (rotor), if it is not you can get this info from your local repair shop, or auto supply shop.

Nov 10, 2009 | 2005 Suzuki Swift

1 Answer

What is the procedure to replace front and rear brake pads on 1 2006 Audi A4 Quattro? It doesz not seem to be the same process as American cars.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Nov 07, 2009 | 2004 Audi A4

1 Answer

Loud noise coming from back passenger side wheel when backing up


sounds more like a brake wear sensor. The inner pads wear faster than the outer, so if you are checking pad wear, be sure to look at the inner pad. If you just had brake work done, one of the anti rattle clips on a pad may be contacting the brake rotor.

Jun 22, 2009 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
1994 Mitsubishi Eclipse Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...