Question about 1995 Ford Aerostar

1 Answer

Fan belt diagharm for 3.0 ford - 1995 Ford Aerostar

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 144 Answers

Here is a serpentine belt diagram for you vehicle. This is for a 1995 Ford Aerostar with a 3.0 liter engine. Have a great day and i hope this helps!!fan belt diagharm for 3.0 ford - b220738.gif

Posted on Oct 04, 2009


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 144 Answers

SOURCE: 3.0 ford belt diagharm

I'm sending you two belt routing diagrams for the 3L one with A/C and one without A/C.
I'm also sending you to more belt diagrams for the 4L, one with A/C and one without A/C.

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Instructions needed for changing serpentine belt on 2002 Ford Windstar 3.8L

  • the serpentine belt routing chart, adhered to the fan shroud. This chart will show you the location of the belt tensioner.
  • 2 Pull the belt tensioner off the belt with the serpentine belt tool. Reach in with your free hand and slip the belt out of the tensioner's path and then slowly move the tensioner back into position.
  • 3 Pull the belt off the remaining pulleys by hand

  • Read more: 2002 Ford Taurus Serpentine Belt Removal '

    Sep 09, 2011 | Ford Windstar Cars & Trucks

    1 Answer

    How replace fan belt for Ford Crown Victoria 2000?

    Mechanical Fan Belt Removal & Installation - Refer to Illustration below

    Ford 4.6L Engine - Ford Crown Victoria, Mercury Grand Marquis, Lincoln Town Car, Marauder

    1. Loosen the fan clutch-mounting shaft from the water pump hub.

    2. Loosen the fan shroud from its radiator mounting and remove the lower hose from the shroud.

    3. Lift the fan and clutch assembly and the fan shroud from the vehicle.

    4. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch.

    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage.

    To install:

    1. Assemble the fan and fan clutch. Tighten the retaining bolts to 15-20 ft. lbs. (20-27 Nm).

    2. Install the fan and clutch assembly and the fan shroud. Mount the fan clutch shaft to the water pump hub and tighten to 37-46 ft. lbs. (50-62 Nm).

    3. Slip the shroud into the lower mounting clips and install the shroud retaining screws.

    Fig. 1


    To view this JPEG image better, you can Right-click on it, "Save Image As..." then
    view it or enlarge it within Microsoft Windows Media Player, or Real Networks RealPlayer.

    Sep 04, 2011 | 2000 Ford Crown Victoria

    1 Answer

    I need a serpentine belt diagram for a 1991 ford thunderbird v-8 5.0


    Fig. 1: Exploded view of the belt drive fan assembly-1992 vehicle shown

    To install:
    1. Position the fan on the drive clutch. Install the bolt and washer assemblies, then tighten to 12-17 ft. lbs. (16-24 Nm).

    2. Position the fan drive clutch, fan assembly and fan shroud, then bolt the fan and clutch assembly to the water pump hub. Install and tighten the clutch retaining bolt and water pump assemblies evenly and alternately to 15-22 ft. lbs. (20-30 Nm) for the 3.8L engine or to 36-47 ft. lbs. (48-65 Nm) for the 5.0L engine.

    3. Install the fan belt. Align the fan shroud and adjust for equal fan-to-shroud radiator clearance but maintaining a minimum of 0.38 inch clearance to the fan tip on 5.0L engines.

    4. Install and tighten the shroud retaining screws. On 5.0L engines, snap the air deflector assembly to the sub-frame cross brace.

    Hope helps (remember to rate and comment this).

    Oct 01, 2010 | Ford Thunderbird Cars & Trucks

    1 Answer

    How do I install a new fan belt?? 2000 Ford Nustang, 3.8

    First you should make a drawing of the routing of the belt. there is an belt tenstioner which you must remove the tenstion on the belt which you can use a 3/8 ratchet. Losen the tenstion and the belt should slid off. make sure the new belt is the same size in legth and number of ribs. Spin all pullys to make sure the spin free and not making a grawling noise.

    Feb 20, 2010 | 2000 Ford Mustang

    1 Answer

    Replacing Serpentine belt 1998 ford taurus

    should show on fan shroud belt routing.
    on idler pully there should be square hole for 3/8 ratchet to go in and turn to loosen belt, but you have to hold pressure on it to take belt off one pully.and also to put back on.
    [watch your knuckles]

    Dec 18, 2009 | 1998 Ford Taurus

    1 Answer

    3.0 ford belt diagharm

    I'm sending you two belt routing diagrams for the 3L one with A/C and one without A/C.
    I'm also sending you to more belt diagrams for the 4L, one with A/C and one without A/C.

    Oct 04, 2009 | 1995 Ford Aerostar

    1 Answer

    Trying to get the fan shroud off a ford ranger

    You should have bolts that go across the front of you shroud and a couple of them down by the fan. To take the fan off you need to pull off the belts so it is free and then you will have more bolts on the front of the fan.

    Mar 24, 2009 | 1999 Ford Ranger SuperCab

    1 Answer

    Noise from ford focus fan belt tensioner

    You could just tighten up the fan belt. Loosen off 3 Bolts on the alternator just enough to be able to move it, then retighten. Stuff the idea of buying a replacement, for something that will last the lifetime of the car.

    Feb 11, 2009 | 2000 Ford Focus

    1 Answer

    2001 Ford Taurus fan belt replacement

    16mm socket along with a 3/8 braker bar or rachet if the car has a remote starter disconnect battery you will see the belt tensioner holding the belt down you will have to put the rachet on there to pry the tensioner away from the belt make sure fingers stay clear and once you get the tensioner off the belt take the other hand and slide the old belt off the alternator I always save the old belt because the new one snaps now you can put the new one on going backwards from the way you removed the old one

    Nov 08, 2008 | 2001 Ford Taurus

    1 Answer

    How do you replace a driving belt on a 1999 AU ford falcon

    start by unplugin the electric fans then remove the two 10mm bolts holding them in, the bottom of the fans are held in by a slot that they sit in so after you remove 2 bolts just lift the fans out. then you will see a tensioner i think it has 3/8 drive square hole in it( could be 1/2'' drive) just pull it down with a long bar with a 3/8 end on it to release the tension, while doing that slide the belt of,. if your car doesnt have a picture diaghram on the under side of the bonnet for drive belt routing draw a picture incorprating all the pulleys an how the belt goes around them. once the belt is of put the new one on exept over the power steering pump pulley, then pull on the tensioner again to release tension and slide the belt over the p/s pulley. these instruction are for the 4.0l falcon motor, the 5.0 v8 is really similar

    Aug 21, 2008 | 1999 Ford Super Duty F 550

    Not finding what you are looking for?
    1995 Ford Aerostar Logo

    Related Topics:

    1,015 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts


    Level 3 Expert

    80339 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers


    Level 3 Expert

    5687 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides