Question about Chrysler Town and Country

Open Question

99 town & country fans not coming on and just changed the relay. how do i fix this?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: 2005 Town Country front blower motor inop fuse/relay ok

Break Down And Replace The Blower Motor


REMOVAL

WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE, THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PERFORMING FURTHER DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE WAY TO DISABLE THE AIR-BAG SYSTEM. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN AN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY OR DEATH OR DEATH.

NOTE: The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed from the vehicle without having to remove the HVAC housing.

  1. Disconnect and isolate the negative battery cable.
  2. Remove the passenger side cowl trim panel.
  3. Position the carpet to access the front upper screw that secures the air inlet housing.
  4. Remove the recirculation door actuator.
  5. Disconnect the blower motor wire lead connector from the blower motor resistor or power module, depending on application.
    1. Remove the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing.
    2. Remove the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing.
    3. Push the rubber grommet through the opening in the lower air inlet housing.
    4. Route the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
    5. Position the recirculation-air door as necessary to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
    6. Gently flex the recirculation air door downward to gain access to remove the blower motor from the HVAC housing. NOTE: To aid in installation, note the position of the blower motor mounting tabs prior to removal
      1. Remove the blower motor from the HVAC housing by rotating and tilting the blower motor as necessary.
      INSTALLATION

      1. Gently flex the recirculation-air door downward to gain access to install the blower motor into the HVAC housing.
      2. Position the blower motor to the HVAC housing and tilt and rotate the blower motor as necessary to install it into the HVAC housing.
      3. Align the blower motor mounting tabs to the locations noted during removal and install the three screws that secure the blower motor to the HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      4. Route the blower motor wire lead through the opening in the lower air inlet housing and seat the rubber grommet.
      5. Position the recirculation door pivot shaft into the lower air inlet housing and install the inlet housing.
      6. Install the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and the lower HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      7. Install the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing. Tighten the screw to 2 N·m (17 in. lbs.).
      8. Connect the blower motor wire lead connector to the blower motor resistor or power module, depending on application.
      9. Install the recirculation door actuator.
      10. Reposition the carpet.
      11. Install the passenger side cowl trim panel.
      12. Reconnect the negative battery cable.
      13. Perform the heater-A/C control calibration procedure.

Posted on Feb 07, 2009

Ad
chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

wmsfarris
  • 22 Answers

SOURCE: where is the cooling fan relay on 2005 chrysler town and country

I am not sure on this one but I think the left front headlight has to be removed. Also I think these are riveted on and you will have to drill the rivets and gently use a chisel to get them off.

Posted on Apr 09, 2009

mcgyver468
  • 710 Answers

SOURCE: Trying to locate cooling fan relay switch?

Driver's side in the fuse/relay box under the hood.

Posted on Apr 25, 2009

keemo68
  • 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 town & counrty (3.8) cooling fans staying on


the radiator temperature is broken or cable to it is disconnected ?
if true they are set to run constant the fans to protect the engine from overheating. also check the relay is still seated correctly.

Dec 23, 2013 | 2007 Chrysler Town & Country LX New Cars

1 Answer

97 chrysler T & C coolong fan


A mechanic would check the fuses and relays first. The computer grounds the relays to power the fans.

Aug 22, 2012 | 1996 Chrysler Town & Country

1 Answer

I have a 1996 town & country 3.8L. I replaced the


You need the system scanned for codes, the fans and controlled by the engine computer.

Jun 16, 2012 | Cars & Trucks

1 Answer

Radiator fans don`t work on town and country van causing engine to overheat


The radiator fan relay is located behind the grill on the driver's side of the vehicle. There is no relay in the distribution box. There is a 40 amp fusible link, however, in that box.
The relay (behind the grill) works in conjunction with the coolant temperature sensor, the A/C high pressure switch, the transmission temperature sender and the PCM. This relay will run the fans from 30% to 99% of full speed based on the signal coming from the PCM. This is all according to the official Chrysler shop manuals that I have for my 2005 Town and Country van.

Apr 23, 2012 | Cars & Trucks

1 Answer

The air conditioning quit. I was told since the radiator fan would not work ( for the air cond. )that was the problem. I checked the fan & it was good so I changed the powertrain control module and...


The fan is controlled by a relay that could be bad, and the relay is controlled by the climate control unit, which could also be bad. Pull the fan relay and see if it the primary is getting voltage, with a test light, when the AC is turned on.

Jul 09, 2010 | 1999 Chrysler Town & Country

1 Answer

Why does my 2005 Town & Country radiator fan


The fan is computer controlled and will not come on untill it reaches 212Deg . It should come on though if you turn on the air conditioning, if not you could have a bad fan relay or relay plug.

Feb 22, 2010 | 2005 Chrysler Town & Country

2 Answers

2003 Dodge Town and Country Van, 3.8 V6. Where is the engine cooling fan relay located? I replaced the blown 40 amp fuse, tested both fans, the are OK. Need to locate relay!


Down by the bottom of the radiator. pass side. on the frame/rad support. You probly have to remove front splash shield to get to it. I have never had to remove or change one.

Jan 23, 2010 | 2003 Chrysler Town & Country

1 Answer

2001 town & country front blower not working


Does that part behind glove box (which is probably resistor) have power going in as well as coming out at both terminals. Take reading on both sides. Did this fan run only on high for a while?

Jul 26, 2009 | 2004 Chrysler Town & Country

1 Answer

Radiator Fans on 01 Town and Country do not come on


Ok, Dont replace anything with out checking .....Pls check your wire Connction By Muilti Meter. I think your has loose Connection.

Jun 01, 2009 | 2001 Chrysler Town & Country

1 Answer

Fan relay


You should the same relay in your vechile just swap it and see what happens.

Aug 06, 2008 | 2001 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...