Question about 1986 Ford Mustang

1 Answer

How to install tach on 86 mustan - 1986 Ford Mustang

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Need to know type of tach, and model number.

Posted on Oct 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tach quit working an speedometer goes crazy what would cause


vss has probably gone bad. vehicle speed sensor ( vss)

Apr 24, 2015 | Cars & Trucks

1 Answer

How to repair or trouble shoot.


The tach itself may be bad. Check with local used parts and get a used one. Should be pretty reasonable to buy the entire dash bezel. Install the entire bezel in your car or carefully remove and replace just the tach

Aug 28, 2014 | 1992 Ford Bronco

1 Answer

Code p1451 de mustan 2000


P1451--Evap Control System Canister Vent Solenoid
Circuit Malfunction

Going forward

Google your codes

Type: OBD & the code

Ford OBD P1451

Aug 13, 2014 | Cars & Trucks

3 Answers

I have and 2003 Mustan Cobra. I was hearing a


You could have a failed wheel bearing. Jack the rear up with the trans in neutral (chock the front wheels please) and try to spin the tire. it should spin fairly easy. If you feel grinding or the wheel is difficult to spin then I would say it is the wheel bearing.

Feb 17, 2010 | 2003 Ford Mustang

1 Answer

How do i adjust the 2 screws on my carburetor on my 86 nissan hardbody (automatic) so it doesnt eat up a lot of gas...??


i use a tach, turn each screw till you get the highest reading on the tach for each screw adjuster.

Jan 27, 2010 | 1986 Nissan Pickup 4WD 1986

2 Answers

86 jetta diesel, high reving 5ht gear


wierd not normal. are you sure you have eased off the throttle enough just before you dip the clutch, diesels can lag slightly, is it a turbo? turbo could create even greater lag

Jan 11, 2010 | 1985 Volkswagen Jetta

1 Answer

Are there 2 fuses for the hassard and turn signals


Sounds like the flasher is bad, that would be the round silver breaker that plugs into the fuse block.

Nov 06, 2009 | Ford Mustang Cars & Trucks

1 Answer

90 civic aftermarket tach wiring


the bleu wire on your distributor plug is your tach signal

most engine

Apr 01, 2009 | 1998 Honda Civic

1 Answer

1989 VW Jetta deisel tach.


You can't, the tach from the gas car reads a signal from the ignition system. Your diesel has no ignition system at all, no can do.

Aug 10, 2008 | 1989 Volkswagen Jetta 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...