Question about 2004 Jeep Liberty

1 Answer

2004 jeep liberty replacing the starter

Steps to replacing the starter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

2004 jeep liberty replacing the starter - 8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front seat removal 2004 jeep liberty


4 bolts.
look first see em,' you will of you look
if wanting to know before looking
there is this magic book, called SM
that does this step by step,
see KJ jeep and read.
http://jeepdied.com/books.html

Feb 20, 2017 | 2004 Jeep Liberty

1 Answer

Where is the position of radiator fan relay on jeep liberty 2006


no idea to be honest earlier jeeps had then at the front of the wing down below as i remember ?? newer one would i imagine be in the electrical box under the bonnet near the battery

Dec 02, 2016 | Jeep Cars & Trucks

1 Answer

I need a step by step instruction on how to change a head gasket on a 2004 jeep liberty.


no engine stated. so.....
step by step. that include tools"?
the full step by step is in the FSM, why not read that.?
factory service manual>? then ask questions.
the first question is why , did you overheat it?
and if yes, the head must be checked for warpage and then pressure checked,
or its just repeats, 90% of all repeats are not doing all steps right.
use jeep gaskets or FELPRO
FSM (real deal)
https://www.techauthority.com/en-US/Pages/FacetSearchResults.aspx?make=Jeep&year=2004&model=LIBERTY+SPORT&producttype=Service+Manuals&ptCatId=3083

clone:
alldata.com 15 bucks

best clone of all

questions to ask self
why it failed
are head bolts re-usable or one time TTY bolts.
and are you having pro look at head and block deck to see if the
surfaces are good to use again , damage has no limts....

Jan 12, 2015 | 2004 Jeep Liberty

1 Answer

2004 JEEP LIBERTY. BATTERY GOOD. THE CAR WILL NOT TURN OVER. IT SOUNDS LIKE IT IS COMMING FROM FUSE BOX UNDER HOOD


I assume you are hearing a starter Relay/solenoid chattering. That's usually caused by:

A dead battery.

A loose connection on Battery or start relay/solenoid.

Bad connection at starter or bad starter.

Good Luck

Jun 29, 2011 | 2004 Jeep Liberty

1 Answer

2004 jeep liberty won't start no click


your key starter might be bad or unplugged

Dec 05, 2010 | 2004 Jeep Liberty

1 Answer

2004 jeep liberty will not start, have power and sounds like starter is clicking but it will not turn over


Chances are battery is in need of replacement. If you can get the battery out and take it to auto parts store, have it load tested.

Mar 07, 2010 | 2004 Jeep Liberty

1 Answer

2004 jeep liberty 3.7 eng will not crank over jump start it will start battery only year old


Sounds like your altenator is bad. Most part stores will test for free, in or out of vehicle. Battery, Alt, and starter can be checked for free.

Oct 16, 2009 | 2004 Jeep Liberty

1 Answer

Change out starter 2004 Jeep Liberty


Starter should be pretty simple but they always put them down below in hard reach areas and pain the *** get out back in . Only has few connection dis connect the battire so you dont shock the hell out of your self.
It be two main bolts that hold into place and few nuts hold wires on.
Get hanes book it help you out some.
Hope this helps you out give thumbs up if it helps you out

Jul 29, 2009 | 2004 Jeep Liberty

1 Answer

How do you reset remote for doors on 2004 jeep liberty.


Go on the jeep.com website and download the owner's manual it's free and it explains it clearly step by step...

Apr 02, 2009 | 2004 Jeep Liberty

Not finding what you are looking for?
2004 Jeep Liberty Logo

5,448 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...