Question about 1996 Jeep Grand Cherokee

1 Answer

Striped out bolt for brake caleper front end

Striped out bolt for brake calaper front end

Posted by on

  • chitownbob45
    chitownbob45 May 11, 2010

    Whats stripped the head of the bolt or the threads from over tightening? If its the head try vise grips if its the threads go to the auto parts store get a new bolt and use some loctite on the threads do not over tighten. If this doesnt work you will have to retap the threads.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Buy heli coil from a/p store

Posted on Oct 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need a tool to take my front passenger caleper off to replace the tire studs it seems to need an allen key


don't know about this exact car, but most brake calipers use either a 3/8th inch allen (hex) head or a T-50 torx head bit. The Hex wrench is what I would get without seeing this. I have also used a ratchet extension on some cars.

Jul 03, 2011 | Pontiac Sunfire Cars & Trucks

1 Answer

I had both front end hubs replaced on my 2004 Siverado 1500 pick up truck. What is a hub?


hub took the place of old wheel bearing know they are seald bearings easy to replace remove brake calaper an three or four bolts an king nut if fourwheel drive sorry i cant spell haha

Dec 16, 2010 | 2004 Chevrolet Silverado

1 Answer

How do you change the front drivers side u joint?


pull wheel, brake caleper, bearing asembly,then alke will come out.

Sep 13, 2010 | 1989 Dodge Ram D-Series Pickups

2 Answers

How difficult is it to cange the front rotors?


depending if you have the tools to do the job and pb blaster lock tite and white and dark grease for a beginer it has a rating of 7-8. if you work on cars and know what your doing, then its easy.. first thing is to remove the calapers then remove the calaper mounting bracket spray around the studs and bolts with pb blaster also around the hub and tap around the whole area around rotor dont hit the studs (with hammer) to break the rust buildup this should break rotor free then you may want to clean the rust off so that the rotors seat properly remove and clean new rotors with brake cleaner to get off the film off them (shipping rust retardent) and wipe. spray bolt holes to clear any rust left while removing old rotor and braket and dry. place a small ring of lock tite on bolts holding caliper brackets and let stand till harden or almost hard. replace new rotors install bracket/s and bolts (torq to ? 80foot lb) while replacing rotors replace brake pads, replacing just rotors will over heat new rotors in spots and warp rotors!!! make sure you pull the pins that retain the calipers to the bracket and add light coat of white grease to pins so calipers slides easy and evenly

Jan 21, 2010 | 2003 GMC Envoy

2 Answers

How to install front brake shoes on 1998 toyota camry


just take off tire take a clip out and pull out front shoe and take off roter then the back push in the cylender with a c clamp and revers the process of the calaper might come off using boltes then same process

Aug 29, 2009 | 1998 Toyota Camry

2 Answers

Remove and replace rotor on the front of an LX station wagon


Start by jacking the car up, place on jack stands for safwety, You will see the brake calaper which holds in the shoes, you will see two bolts which holds the brakes together, remove these bolts, then remove the pads. Remopve the bolt and pen holding the rotor on, take the rotor to a brake shop, see if it can be turned instead of having to purchase a new one. When replacing the brake pads you will have to use one of the pads to push the pressure plate back into the calaper to replace the pads. You may want to remove some of the brake fluid so it wont over flow when doing this.

Aug 07, 2009 | 1994 Honda Accord

1 Answer

How to change rear brake pads on audi a6 2006


Remove the tires, Remove the calaper bolts, (small heads on them 12mm or so) Remove calaper, Pads are setting in a holder. Lube new pads with litheum grease and place in holder. (look at old pads, one or both may have small metel tab on one end) If the new pads have the tab, put that pad where the old pad with the tab was. (ie. tab to the inside) Press pistion in with a 'C' clamp. If it won't go in easly, it may screw in. If the parking brake cable is hooked to the calaper, it probly screws in. Use large pliers to screw in calaper piston. Place calaper over pads and install bolts (lube bolts) Rember to pump brakes befor driving . to get a solid peddle.

May 20, 2009 | 2006 Audi A6

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...