Question about 1994 Acura Integra

1 Answer

Why won't my 1990 acura integra go over 4000 rpm?

Why won't my 1990 aura integra go over 4000 rpm?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Acura Expert
  • 268 Answers

Could be fuel filter. This will restrict a lot. If it is automatic it might be your transmission control module. Your check engine light should be coming on if it's not already.

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Acura starts & runs fine but has been stalling out when accelerating after stopping at an intersection.


1) Turn on all electric systems- AC/wipers/radio/lights etc

2) if car stalls randomly at low RPM - Replace the Alternator
These cars are very sensitive to fluctuations in voltage and it will stall.

Aug 06, 2013 | 1990 Acura Integra Hatchback

1 Answer

What is the torque spec's on a acura integra gs 90 motor ?


1990-1991 OBD0*
Engine: B18A
Cylinder Arrangement: Inline 4 Cylinders, Transverse
Type: Water cooled, 1.8L, 4 cylinder, 16 valve, DOHC
Displacement: 111.9 cu in (1834 cc)
Bore & Stroke: 3.19 in x 3.50 in (81mm x 89mm)
Compression Ratio: 9.2 : 1
Valve Train: Double Overhead Camshafts, Belt Driven
Fuel System: Programmed Fuel Injection (PGM-FI)
Horsepower: 130 hp @ 6000 rpm
Torque: 121 lbs.-ft. (16.8 kg-m) @ 5000 rpm
Redline: 6500 RPMs
Engline Block: Aluminum Alloy with Cast Iron Cylinder Liners
Cylinder Head: Aluminum Alloy

Jun 24, 2010 | 1990 Acura Integra Hatchback

1 Answer

How to set the timeing on 1990 acura integra


YOU NEED TO CONNECT A TACHOMETER ACCORDING TO THE MANUFACTURERS INSTRUCTION.ON THE 1990 - 1993 MODELS USING A SUITABLE JUMPER WIRE CONNECT THE GREEN AND BROWN TERMINALS OF THE IGNITION TIMING ADJUSTING CONNECTOR LIGHT GRAY WIRE LOCATED UNDER THE RIGHT SIDE OF THE DASH.MAKE SURE ALL WIRES CLEAR OF THE COOLING FAN AND HOT EXHAUST MANIFOLDS.START THE ENGINE POINT THE TIMING LIGHT AT THE TIMING MARK POINTER AND THE CRANKSHAFT PULLEY.ON THE 1990 - 1993 MODELS THE POINTER SHOULD BE ON THE RED MARK 16 DEGREES BTDC ON THE CRANKSHAFT PULLEY AT 700 - 800 RPM.IF NECESSARY ADJUST THE TIMING BY LOOSENING THE DISTRIBUTOR ADJUSTING BOLTSSLOWLY ROTATE THE DISTRIBUTOR IN THE REQUIRED DIRECTION WHILE OBSERVING THE TIMING MARKS.AFTER MAKING THE NECESSARY ADJUSTMENT TIGHTEN THE HOLD DOWN BOLTS TAKING CARE NOT TO DISTURB THE ADJUSTMENT.REMOVE THE JUMPER WIRE.

Feb 28, 2010 | 1990 Acura Integra Hatchback

1 Answer

I need a diagram for interior fuse box panel 1990 acura integra


Easiest way to do this is go to a junkyard and take one off another car. shouldn't cost more than a couple dollars. You won't even need tools it's a plastic hand screw.

Jul 14, 2009 | 1990 Acura Integra Hatchback

1 Answer

1990 acura integra - was driving car and all the sudden the engine quit and RPM's dropped. have plenty of gas, what are the possibilities/problem. Car will now not start


depends. First check for fuel and spark. Its rare a honda pump go out but it does happen. It has happened to me a couple times. Ive owned 14 hondas so this should be accurate. The ignition control module is located in the distributor, its a small square black piece that has four wires pluged onto it. Have that checked and also the coil. We'll go from there for now

Jan 17, 2009 | 1990 Acura Integra Hatchback

1 Answer

Belt replacement 1990 acura integra


Ok, you will need a 10 mm socket and extension and a 14 and 15 mm wrench. One of the "idler" pullies is actualy an adjustable tension pully. loosen the center nut on the pully, and then begin loosening the 10 mm bolt from above. as you loosen it, the pully will drop, and soon enough you can slip the belt off.
good luck

Dec 14, 2008 | 1990 Acura Integra Hatchback

1 Answer

1990 Acura Integra Vin codes


The vehicle grade is denoted in the 6th digit, in your case "4" indicates an RS model.

Oct 19, 2008 | 1990 Acura Integra Hatchback

Not finding what you are looking for?
1994 Acura Integra Logo

Related Topics:

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...