Question about 2003 Mercedes-Benz C-Class

1 Answer

Where is the location of the place to put in clutch fluid

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 22 Answers

It is brake fluid container, the same fluid for brakes and clutch.

Posted on Oct 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Parts diagram for clutch slave cylinder nissan D40


It's easy put new master cylinder in place but don't connect rod to clutch pedal or bolt it to bulk head and leave metal solace feed pipe undone , connect fluid feed pipe to cylinder then tilt cylinder so slsve out let faces more down wards then top up fluid pot when fluid runs out slave outlet reconnect slave pipe , bolts master cylinder back in place and connect pedal to it , then undo nipple on slave cylinder let fluid run out freely titghten niplle then pump clutch pedal until it becomes firm job done .
15 minute job .

Nov 07, 2015 | 2007 Nissan Navara 2.5

1 Answer

No clutch master cylinder reservoir on my 84 AMC Eagle.


Check the master cylinder on the brake and see if there is a line connecting to the slave cylinder. otherwise it should be mounted on the firewall where the clutch comes through the firewall.

May 21, 2013 | 1984 AMC American Motors Eagle

1 Answer

Where can i locate to put tansimittion fluid in my 87 might max manuel clutch


first of all it takes clutch fluid or dot 3 brake fluid the resivoir is usually located on driver side under hood on fire wall should be up high & close to brake fluid resvoir it will be round & small after filling pump pedal up& down quickly until you get pressure then have someone else open bleeder valve down on side of bell housing while holding pedal down closing it back & repeat until pedal has good feel if this doesnt work then one or the other is bad the master cylinder or slave cylinder is bad & needs replacing good luck with this info

Mar 03, 2013 | 1994 Mitsubishi Mighty Max

1 Answer

Where is the clutch fluid refill located on a 1998 toyota rav4. I found the brake fluid reservoir, but am not seeing a reservoir for clutch fluid. Any help


If you look at the drivers side of the brake fluid reservoir you should see a rubber hose that feeds to the clutch master cylinder. The clutch master cylinder is kept full via the brake fluid reservoir.

Dec 30, 2012 | 1998 Toyota RAV4

1 Answer

Where do i put clutch fluid?


This is for a 328, but should be the same for a 325.

Location 1 is where you add the clutch fluid. The brake fluid reservoir for both the brake master cylinder and clutch master cylinder. There is a line from the brake reservoir to the clutch master cylinder.

Also, read you owners manual. It should show the same ocation pictorially.

dimitrios_ga.gif

Dec 30, 2010 | 1999 BMW 328 Series

2 Answers

When I put the clutch down it squeals I am thinking it needs transmission fluid but can't find where to put it


I don't believe that you would need more transmission fluid if you have a squeel (but for future reference clutch fluid is located with the brake fluid and uses brake fluid DOT 3). Squeeling is usually a tall tell sign that your clutch or pressure plate is going out. Also for future reference the actual transmission fluid will be on the side of the transmission and should say oil, if not it is usually 3 to 5 inches from the lowest point on the transmission and may take a certain weight (80-90W, 75-90W, etc.

Aug 22, 2010 | 2000 Daewoo Nubira

1 Answer

1987 Maxima-5 speed is difficult to grt in to gear--How to adjust clutch and check clutch hydraulic fluid?


TO ADJUST PEDAL HEIGHT ADJUST WITH A STOPPER LIMITING THE UPWARD TRAVEL OF THE PEDAL.PEDAL FREE PLAY IS ADJUSTED AT THE MASTERCYLINDER PUSH ROD.IF PUSH ROD IS NON ADJUSTABLE FREE PLAY IS ADJUSTED BY PLACING SHIMS BETWEEN THE MASTERCYLINDER AND THE FIREWALL.ON A FEW MODELS PEDAL FREE PLAY CAN ALSO BE ADJUSTED AT THE OPERATING SLAVE CYLINDER PUSHROD.PUSHRODS ARE AVAILABLE IN THREE LENGTHS FOR THE 310.PEDAL HEIGHT ABOVE FLOOR IS 6.73 - 7.13 INCH PEDAL FREE PLAY IS 0.04 - 0.12 INCH.YOU HAVE CLUTCH FLUID LONG AS YOU SEE BRAKE FLUID IN MASTERCYLINDER.IF MASTERCYLINDER LOW YOU HAVE TO BLEED THE THE CLUTCH MASTERCYLINDER BY LOCATING BLEED SCREW ON SLAVE CYLINDER. REMOVE THE BLEED SCREW DUST CAP.ATTACH A CLEAR TUBE TO THE BLEED SCREW.PUT OTHER END OF CLEAR TUBE IN A CLEAN CONTAINER OF BRAKE FLUID.FILL THE MASTERCYLINDER WITH BRAKE FLUID.OPEN BLEED SCREW 3/4 A TURN.DEPRESS CLUTCH PEDAL QUICKLY.HOLD IT DOWN.HAVE A HELPER TIGHTEN THE BLEED SCREW.ALLOW PEDAL TO RETURN SLOWLY.BLEEDER SCREW TORQUE IS 5 - 6 FT LBS.IF YOU SEE AIR BUBBLES CLEAR BLEED TUBE.REPEAT THE BLEED PROCESS UNTIL YOU SEE NO AIR BUBBLES.DONT LET CLUTCH MASTERCYLINDER GO DRY WHILE BLEEDING.IF SO YOU GOT START BLEEDING PROCESS ALL OVER.HOPE THIS HELP.

Aug 05, 2010 | 1987 Nissan Maxima

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

1 Answer

My 1988 Saab 9000 Turbo needs hydraulic fluid for the clutch. Where is the place where I put the hyrdralic fluid located???


the clutch is fed by the brake's .. its actuallly jsut break fluid.. if your low on clutch fluid it means you must have a leak check the master it self for leaks.

Sep 28, 2009 | 1989 Saab 9000

1 Answer

Help..where to put clutch fluid in 01 tt


Your hydrolic clutch fluid resivor is usualy located next to your master cyllender, where you put your brake fluid in. It is usualy a small round plastic container with a screw cap on it located near the master.
Good luck

Dec 16, 2008 | 2001 Audi TT

Not finding what you are looking for?
2003 Mercedes-Benz C-Class Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...