Question about 2004 Chevrolet TrailBlazer

1 Answer

Washer fluid motor will not shut off - 2004 Chevrolet TrailBlazer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Check switch, manually turn off or lubricate switch with silicone spray lubricant 

Posted on Oct 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

1 Answer

Why what my Windshield washer fluid lamp will not shut off. It is full. States that i need to add windshield washer fluid and it is full, how do you reset the sensor. ?


what kind of car do you have ,?and year make model,motor size, is very importaint, some cars like chevy 02 you have to turn key on and pump brake 3 times and that clears washer fluid light, so now you know why we need other info. Woody

Sep 26, 2014 | Cars & Trucks

2 Answers

Windshield washer not working


  1. check your windshield washer fluid level.
  2. make sure you can hear the fluid pump operating when you operate the switch.
  3. If you can hear the pump working and you have fluid in the reservoir but still no spray,
  4. check the washer fluid lines don't have holes and aren't clogged or pinched. check the sprayer nozzles make sure they are not clogged with debris.
  5. if your washer still doesn't work your fluid pump is probably the problem.

Sep 28, 2013 | 1999 GMC Jimmy

1 Answer

How do you change over the window washer motor?


Hi! sandrkayesi
Due to multiple locations of washer motors I could use more specifications. Could you clarify Year and brand and model. When you say washer motor, is this the washer fluid Motor or the Wiper Motor. The older models these two units were combined. On newer Models the fluid pump is mounted on the washer fluid tank.
InMrFixiIt

Jun 25, 2011 | Ford Festiva Cars & Trucks

2 Answers

No windshield washer fluid pumping


1) Fluid resevoir is empty
2) Fluid is frozen
3) Washer fluid hose is disconnected, blocked or kinked
4) Washer switch is faulty
5) Washer pump motor is defective
6) Washer pump fuse is blown

Dec 24, 2010 | 2003 Oldsmobile Alero

1 Answer

Windshield washer tank will not hold fluid. Runs out at the bottom spout, I see no cracks. Is there a shut off on it?


the washer motor is inside this reservior and the washer pumps seal is leaking on you

Feb 27, 2010 | 2008 Mercury Sable

1 Answer

Washer fluid pump not humming or trying to push fluid to windshie


disconnect the connector and have a friend push the washer button while you check the wires for power with a test light.its probably a bad motor, they are about $15.00

Dec 22, 2009 | 2002 Toyota Highlander

2 Answers

The rear wiper on my '99 model exped isnt working ,ford global says its the motor and it will cost me P13k . any one who can help me find a mechanic do some repair on this?


what is P13K?

check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

Principles of Operation
NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
There are two distinct modes of wiper operation:
  • Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
  • Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.
To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
Inspection and Verification
  1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .
  1. Verify the customer concern by operating the wiper/washer system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Hoses to windshield washer pump
  • Wiper linkage
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
  • Wiring harness
  • Loose or corroded connector(s)
  • Relays
  • Motors
  • Multifunction switch
  • Washer fluid level switch


----------------------------------------
  • The wipers are inoperative — rear
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
  • Circuitry.
  • GEM.
  • Multifunction switch (wiper/washer switch).
  • Rear wiper up relay.
  • Rear wiper down relay.
  • Rear wiper motor.

May 12, 2009 | 1999 Ford Expedition

1 Answer

Windscreen washer.


WASHER MOTOR 1. With the washer motor installed to the washer tank, fill the washer tank with washer fluid. 2. Attach the positive (+) lead from the battery to terminal 2, and negative (-) lead to terminal 1. 3. Check that the washer motor runs and washer fluid is ejected.50a9b90.gif SERVICE ADJUSTMENT PROCEDURES 1. Check the washer fluid contact point. 2. Adjust the washer fluid contact point by using a metal wire to move the washer nozzle ball.4a5c2e0.gif48e95c0.gif 3. If the amount of washer fluid is too small, check for clogged, bent or crushed washer piping. Check the chipped points too, because the tube might be crushed.

Jun 25, 2008 | Hyundai Motor 1995 Accent

Not finding what you are looking for?
2004 Chevrolet TrailBlazer Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...