Question about 1993 Saab 9000 Hatchback

1 Answer

I have a saab 9000 1993 which the clutch master cylinder bracket broke in to pieces

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Go online or salvage yard to purchase new or used bracket 

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1987 saab 9000 turbo transmission


bad pressure plate or stuck throw out bearing.

Jun 06, 2012 | Saab 9000 Cars & Trucks

6 Answers

SAAB manual gearbox fluid check & fill location


http://en.allexperts.com

http://www.ptdoityourself.net/tl/tl_indexmain.html

above links will help u get step by step information to solve all problems regarding almost all the cars .

feel free 4 further assistance .rate the particular experts solution as fixya that helps u understand n solve ur problem

Jun 26, 2008 | 1995 Saab 900

1 Answer

My problem is that the manual transmission is stuck in 4th gear. I was backing up when I went to put it into 1st the shifter was stuck. The clutch works to disengage the gears but the shifter won't...


That cylinder is known as the clutch slave cylinder. It should push against the clutch fork every time the clutch pedal is depressed to allow gear changes. If it doesn't, suspect a faulty slave cylinder, or clutch master cylinder.

Sep 09, 2011 | 1999 Nissan Sentra

1 Answer

I'm trying to replace the clutch master cylinder on my 1993 Saab 900s. I found it under the hood but it looks to be mounted from the inside. I'm guessing that I have to remove the dash to access it...


In the first place its called a slave cylinder. usually by means of bracket or bolted directly to fire wall diconnect fluid lines,unbolt & removemake sure you bleed the new one

Jun 16, 2011 | Saab 900 Cars & Trucks

1 Answer

Saab 9-3


First check to see if the master cylinder is full of fluid, if it is then you may have a bad master cylinder or slave cylinder out. If you find a leak then you have found your problem if it's low n fluid you will have to bleed the system, if you need instructions on doing this just post a answer t o this question and I will tell you how to do it. It will require one wrench and brake fluid to bleed the system, if you need to replace the slave or the master cylinder you will need tools to replace these items and I don't have any ideal if you want to repair this yourself or not or what it will cost to fix. Normally the clutch pedal will feel mushy or soft if the slave or master is out and this would cause it hard to get into gear. Let me know so I can help.

Jan 15, 2010 | 2003 Saab 9-3

1 Answer

My 86 Fiero SE clutch master cylinder is weeping


Replace it. Not a difficult job. Be careful the bracket on the V6 4spd. isn't strong so don't break it while loosening the slave cylinder retaining nuts.

Good luck,

Rebel Faggioli

Dec 30, 2009 | 1986 Pontiac Fiero

1 Answer

Manual transmission clutch will engage


There are two possibilities to consider:
  1. the master cylinder is leaking/by-passing hydraulic fluid
  2. the slave cylinder is leaking/by-passing fluid
You didn't mention a fluid leak, so that would eliminate the obvious cause of a leaking pipe. However, check for leaks around the master cylinder (on the firewall) and at the front of the engine by the clutch itself. This would indicate which of the two might be the problem, If they haven't been replaced in many years, it's probably sensible to replace both at once. The slave cylinder can be replaced without removing the engine. If you have ABS, you'll likely need to loosen/remove the alternator.

Good luck!

Saabreur

Jul 12, 2009 | 1988 Saab 900

1 Answer

Where is slave cylinder for clutch on 1994 Isuzu pickup 2.3 litre


To determine which type of clutch you have, servo hydraulic or cable.
Look down past the engine bell housing and determine the existance of a hydraulic clutch slave cylinder.(a piece of casting with a rod facing towards the rear of the vehicle pocket into a bracket protruding out of the gearbox bell housing. As well as a pipe and bleed nipple to be crude)
(which I believe you have).The hydraulic fluid for this unit is sourced from the brake master cylinder reservoir via a sneaky pipe partially obscured to the clutch master cylinder on the internal firewall.If you have no clutch slave cylinder near the bell housing there would be an obvious bounden cable running from the firewall down to the outer of which will be stopped at a bracket hanging off the engine.The inner will continue to a bracket protruding from the gearbox bell housing.

Mar 04, 2009 | 1994 Isuzu Pickup

1 Answer

How to fit a clutch master cylinder for c220 cdi


Remove the three 13mm nuts holding the pedal bracket to the bulkhead, this will give you more room to work but just as it's free to move about a bit. Undo the two 10mm nuts holding the cylinder to the pedal assy and the pipe union at the bottom of the cylinder. Pry off the clutch hose at the fluid reservoir. Release the circlip on the end of the cylinder rod on the pedal.
When you put the new one in feed the hose through first with a piece of wire so you can locate it at the fluid reservoir, loosley connect the union at the bottom of the cly, and pop the end of the cyl rod into place and replace the circlip. now try to relocate the long bolts into the cylinder body, it's a fiddle but can be done. Use a 3/8 drive to undo and re-do the 10 mm nuts as a smaller one seems better but doesn't have the reach. The rest is just common sense.

Aug 01, 2008 | 2000 Mercedes-Benz C-Class

Not finding what you are looking for?
1993 Saab 9000 Hatchback Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...