Question about 1998 Volkswagen Passat

1 Answer

Key fob not working car will lock with the key but some times one door will just open

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 507 Answers

Could be remote battery could be central locking actuator in the door not working to operate the other locks

Posted on Oct 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford explorer sport trac. Door lock buttons do not work. Fob does not work. must lock with key. Doors are very hard to open.


You can reset your fob. Here's a link on how to reset fob,if you have 2,then do at the same time,when 1st fob is done ,push any button on second one asap. http://www.keyfobprogram.com/2005-ford-explorer-remote-programming

Aug 30, 2017 | Ford Cars & Trucks

1 Answer

Key remote won't lock the door change fuse and battery in remote still don't work


Common Reasons Why Your Car Door Isn't Locking Properly The key fob battery is dead: This is one of the most common reasons why your car door lock is not working. If your locks aren't working, replacing the battery in the key fob could solve the issue. The key fob is faulty: If the battery isn't the problem, the issue may be with the fob itself. If you go to your car dealer, they can hook the fob up to a computer and make sure that the programming is still good. If it's not sending a signal, the fob will likely have to be replaced. A fuse is blown: If one door doesn't work, but others do, the problem could be a blown fuse. Replacing the fuse will correct the problem. This is a cheap and easy fix The solenoid is bad: Again, if one door doesn't work, but others do, the problem could be with the door lock solenoid. Replacing it may require removing the car door panel You have a broken wire: If the lock isn't getting power, hold the lock switch either up or down, and then open and close the door repeatedly to see if the lock will work. If it works sometimes, you probably have a broken wire

Sep 28, 2016 | Cars & Trucks

1 Answer

I need to disable an immobiliser on my mg/tf car


If your key fob has just stopped working try this:

  1. Unlock your vehicle with the key in the drivers door lock, do not open the door.
  2. Press the right hand button lock button (the button with the padlock symbol or the dimpled button) on the key fob 4 to 8 times.

If the above fails try this:

  1. Open the key fob
  2. Remove the battery
  3. Press any button 10 ten times, and the same with the other button
  4. Refit the battery or a new battery
  5. Unlock the vehicle with the key in the drivers door lock, do not open the door
  6. Press the right hand button lock button (the button with the padlock symbol or the dimpled button) on the key fob 4 to 8 times

Nov 15, 2012 | MG TF Cars & Trucks

1 Answer

Is have recently replaced my battery in my circle fey fon for an mgtf 2003 how do I connect this so the alarm discounts and I can actually get in my car


If your key fob has just stopped working try this:

  1. Unlock your vehicle with the key in the drivers door lock, do not open the door.
  2. Press the right hand button lock button (the button with the padlock symbol or the dimpled button) on the key fob 4 to 8 times.

If the above fails try this:

  1. Open the key fob
  2. Remove the battery
  3. Press any button 10 ten times, and the same with the other button
  4. Refit the battery or a new battery
  5. Unlock the vehicle with the key in the drivers door lock, do not open the door
  6. Press the right hand button lock button (the button with the padlock symbol or the dimpled button) on the key fob 4 to 8 times

May 28, 2012 | 2004 MG TF 120

1 Answer

Sorry my car was not listed so picked Altima 2003 Micra Intelligent key fob not working properly. Can drive the car but cannot open or lock the doors. Did get fob wet. Now dried out. Worked for first few...


You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | Nissan Altima Cars & Trucks

1 Answer

How come on a 2002 GMC Denali if you lock your key inside


i would say the theft module saw the door trying to be open without the door lock or fob first, once the door lock button was pushed it shut down, it new doors were trying to be unlocked in a theft manner, once shut down it needs time to reset or needs to see ignition cycle with key and read chip in key, smart system isnt it, good luck.

Oct 21, 2009 | 2002 GMC Yukon Denali

1 Answer

Remote key fob won'tprogram


1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 13, 2009 | 1999 Ford Escort

1 Answer

Door locks problem with one door drivers door


dont blame the idiot,we all make stupid mistakes without thinking and iam no exception,remove door trim and oil the solonoid with a oil can not a silly sunday mechanic spray and let it soak in as its working but i think its just a bit sticky with wear and dirt ingress hence it locks but doesnt unlock which might need a bit more power,oil the whole lot lock and all

Dec 05, 2008 | 2000 Renault 181

1 Answer

How do i reprogram my02 ford focus remote locking key fob please.


get in your car close door hit the unlock button then put key in the ignition cycle the key from off to on (STOP BEFORE START POSITION) cycle key off to on 7 times after the 7th trime the doors should lock the unlock automatically that means u are in trainning mode hit the unlock button on key fob. the key fob should now work if it doesn't then try changing batt

Nov 27, 2008 | 2001 Ford Focus

Not finding what you are looking for?

Open Questions:

See all 1998 Volkswagen Passat Questions

1998 Volkswagen Passat Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80417 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...