Question about 2003 Hyundai Tiburon

1 Answer

Hi, I just installed a new Throw-out bearing,pressure plate, clutch disc and dual mass flywheel on my 03 2.7 5 spd Tiburon. I can depress the clutch pedal half way and it becomes rock hard. I know if I press any harder it will break the master cylinder and /or the plastic end that connects to the pedal. I did this once before and remember having to undo the arm that connects to the throw -out bearing shaft (I think, really do not remember) All -Data shows nothing. Really would appreciate some help. Chuck

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,619 Answers

Hi

Thanks for using FixYa. There is a little part located in your clutch slave cylinder called a "delay valve". The part has a small hole in it, and a spring. The clutch slave cylinder in and of itself is pretty simple. Don’t confuse it with the clutch MASTER cylinder located on the cars firewall. Just remove the slave cylinder, unbolt the side with the hose on it, and you should see it, (the valve) and a small spring.


Once these are out, and you have properly installed and done an air bleed of the slave prepare to be amazed. The clutch will now work fine.

Caution.. If you have replaced your clutch, or have a badly worn clutch, this mod will save your existing clutch, but if it’s already so bad that most of the clutch friction material, or the flywheel has been overheated bad enough to cause judder, you will still need to replace the clutch and possibly the flywheel.

Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks

Rylee

Posted on Oct 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 holden epica 2.5l manual has noise only when clutch is depressed


The throw-out bearing is worn and making the noise. The bearing only have pressure on it when the clutch is depressed.
Advise to have new clutch plates installed along with new throw-out bearing since it's all apart anyway and just a few more dollars for the clutch plates. It's a lot of labor.

Good Luck

Sep 22, 2017 | Holden Cars & Trucks

Tip

2004 Hyundai Tiburon Clutch.


First you need to remove the Transaxle.

Manual Transaxle System REMOVAL

1. Remove the engine cover.
2. Remove the battery terminal.
3. Remove the air duct.
4. Remove the battery tray.
5. Remove the air cleaner.
(1) Upper
(2) Lower
6. Remove the back-up lamp switch.
7. After removing the CKP sensor, O2 sensor and oil pressure switch wiring bracket, separate the connectors.
8. Remove the brake fluid leveling sensor connector.
9. Remove the speedometer driven gear connector.
10. Remove the clutch release cylinder mounting bolt.
11. Remove the cotter pin of the shift cable (transaxle side).
12. Remove the cotter pin of the select cable. (transaxle side)
13. Remove the clip of the shift cable (transaxle side).
14. Remove the clip of the select cable (transaxle side).
15. Separate the steering column shaft joint.
16. Separate the power steering oil pump hose.
Be careful not to leak after separating.
17. Separate the hose after removing the clip of the power steering return hose.
18. Remove the upper connecting transaxle bolt.
19. Separate the start motor.
20. Install the engine support fixture.
21. After removing the tire, remove the caliper.
22. Remove the transaxle side cover.
23. Remove the transaxle side under cover.
24. Separate the tie rod end.
25. Remove the wheel speed sensor and the knuckle mounting bolt.
26. Drain the oil.
27. Remove the transaxle mounting bracket.
(1) Insulator bolt
(2) Body side mounting bolt (Upper)
(3) Body side mounting bolt (Side)
(4) Transaxle side mounting bolt.
28. Remove the front roll stopper.
(1) Insulator bolt
(2) Stopper bolt (Upper)
(3) Stopper bolt (Lower)
29. Remove the rear roll stopper.
(1) Insulator bolt
(2) Stopper bolt
30. Remove the drive shaft.
31. Remove the front muffler.
32. Remove the sub frame mounting bolt.
33. Install the transaxle jack.
34. Remove the transaxle lower mounting bolt to the engine.
35. Remove the transaxle assembly.

INSTALLATION
Installation is the reverse of the removal.

Then inspect and replace the clutch place and pressure plate.

INSTALLATION
1. Apply multipurpose grease to the release bearing contact surfaces and the release cylinder contact surface of the clutch release fork assembly.
When installing the clutch, apply grease to each part, but be careful not to apply excessive grease. It can cause clutch slippage and judder.
2. Apply multipurpose grease into the groove of the release bearing.
3. Apply multipurpose grease to the clutch release lever fulcrum contact surface of the clutch release fork assembly.
4. Clean the surfaces of the flywheel and pressure plate thoroughly with fine sandpaper or crocus cloth, and make certain that all oil or grease has been removed.
5. Apply a small amount of multipurpose grease to the clutch disc splines and input shaft splines.
Do not apply more grease than necessary. Too much grease could cause clutch slip or judder.
6. Using the special tool, install the clutch disc to the flywheel. When installing the clutch disc, be sure that the surface having the manufactures stamp is towards the pressure plate side.
7. Install the the clutch cover assembly onto the flywheel and install the six (6) bolts through the clutch cover into the flywheel.
8. Tighten the bolts by one or two turns at a time, in succession, to avoid bending the cover flange.
If a special tool is not available, tighten the bolt temporarily and then torque to specification in diagonal torquing sequence indicated below.
TIGHTENING TORQUE
Single mass flywheel:
15~22 N·m (150~220 kg·cm, 11~16 lb·ft)
Dual mass flywheel:
20~27 N·m (200~270 kg·cm, 14~19 lb·ft)
9. Remove the special tool.
10. Install the transaxle. (Refer to GROUP - Manual Transaxle Assembly)
11. Adjust the clutch pedal free-play. (See CH-6)
INSPECTION
1. Check the diaphragm spring end for wear and uneven height.
Replace if wear is evident or height difference exceeds the limit.
2. Check the pressure plate surface for wear, cracks and color change.
3. Check the rivets for looseness and replace the clutch cover assembly if necessary.
CLUTCH DISC
1. Check the clutch facing for loose rivets, uneven contact, deterioration due to seizure, adhesion of oil, or grease, and replace the clutch disc if defective.
2. Measure the rivet sink and replace the clutch disc if it is out of specification
3. Check for torsion spring play and damage and if defective, replace the clutch disc.
4. Clean the splines on the input shaft and install the clutch disc.
If the disc does not slide smoothly or if play is excessive, replace the clutch disc and/or the input shaft.
CLUTCH RELEASE BEARING
The release bearing is packed with grease. Do not use cleaning solvent or oil.
1. Check the bearing for seizure, damage or abnormal noise. Also check the diaphragm spring contacting points for wear.
2. Replace the bearing if the release fork contacting points are worn abnormally.
INSTALLATION
Installation is the reverse of the removal.
Then remove pressure plate and Clutch plate.

1. Insert the special tool (that came with your clutch kit) in the clutch disc to prevent the disc from falling.
2. Loosen the bolts that attach the clutch cover to the flywheel in a star pattern.
3. Loosen the bolts in succession, one or two turns at a time, to avoid bending the cover flange.

on Jan 13, 2010 | Hyundai Tiburon Cars & Trucks

1 Answer

Clutch installation


Genewrally speaking you need to remove the gear box. UNdo the bolts holding the clutch pressure plate on the flywheel. . Do this by undoing each bolt a few turns at a time. Remove pressure plate and clutch plate. Clean flywheel face. Remove bearing at center of crankshaft and replace as it will be dry and probably rusty. Fit new clutch plate taking care to observe the correct way the plate is fitted. Normally the raised hub section faces away from the flywheel. THis can be checked by pressing the plate against the flywheel and turning it and it it hits the crank bolts you have it in the wrong way round. Fit the pressure plate over the plate and insert the bolts. Some units have 2 or 4 bolts longer than the restand this is to allow the plate to be depressed a fraction to allow the other bolts to screw in. Place a clutch aligning tool through the clutch plate and into the bearing. Evenly retension the pressure plate bolts going alternately across the cover a bit at a time . When retensioned remove the clutch aligning tool. Remove and replace the throw out bearing on the clutch release forks. Ensure that the clutch kit is all new as mixing parts will not work. Refit the gear box. Basically that is the proceedure but to be exact get the manual for your vehicle to cover any extra steps needed for that vehicle.

Mar 07, 2013 | Ford Transit Connect Cars & Trucks

1 Answer

WHERE IS THE GEARBOX THRUST BEARING ON A 2003 JETTA TDI SITUATED AND HOW DO YOU REPLACE IT. WHEN THE CAR IDLES THERE IS A SOUND COMING FROM THE GEARBOX AT THE PREASURE PLATE SIDE. WHEN CLUTCH IS ENGAGED...


This sounds more like a DMF problem (dual mass flywheel) If the car has more than 80K on it.. or the clutch was replaced but the flywheel was not.. you probably have one or more weakened springs in the DMF.

The throw out/thrust bearing is located between the pressure plate and and the transmission itself.

Best of luck

Apr 13, 2011 | 2003 Volkswagen Jetta TDI

1 Answer

Replaced master cylinder in clutch in an attempt to stop the car sticking in gear and moving when foot taken of brake. It still moves while the clutch is still depressed and needs brake to stop...


Sounds like a worn-out clutch plate or broken/damaged throw-out bearing or pressure plate. You need to replace the clutch - including the pressure plate, throw-out bearing, pilot bearing, and I also recommend a new slave cylinder. (Especially since you have allready replaced the master cylinder.) You may want to weigh the pros and cons of having your flywheel machined or just replacing it with a "Remanufactured " flywheel.

Mar 13, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

92'isuzu pick-up, 2.3L.manual tran. the truck starts and it goes into all gears, but it hardly moves.I adjusted the clutch cable and it got better I always had to adjust the cable. now it bearly move on...


Yes it is time to install a new clutch kit(clutch disc,pressure plate ,throw out bearing and pilot bearing)also have the flywheel resurfaced.The disc has gotten too thin to be clamped by the pressure plate.Best if you replace everything at once with new parts,avoid rebuilt parts.Good luck!

Mar 06, 2011 | 1992 Isuzu Pickup

1 Answer

1998 ford contour 2.5 ltr manual,stuck in second and have to hold the clutch in to move it.how do i solve this issue?


SECTION 308-00: Manual Transmission/Transaxle and Clutch - General Information 1998 Contour/Mystique Workshop Manual DESCRIPTION AND OPERATION Manual Transaxle and Clutch Manual Transaxle and Clutch - General Information This section covers general procedures for diagnosis and testing the clutch system. For additional information, refer to Section 308-01 . For specified clutch system service procedures. For additional information, refer to Section 308-02 . For a complete description of the manual transaxle. For additional information, refer to Section 308-03 .
The clutch system includes:
  • Flywheel.
  • Clutch disc.
  • Clutch pressure plate.
  • Clutch master cylinder.
  • Clutch slave cylinder.
  • Clutch release fork.
  • Clutch release hub and bearing.
The clutch master cylinder transmits fluid pressure to the slave cylinder, which in turn moves the clutch release fork and the clutch release hub and bearing.
The clutch master cylinder uses brake fluid and shares a common reservoir with the brake master cylinder
The clutch is a single plate, dry-friction disc with a diaphragm-style spring clutch pressure plate. The clutch disc has a hub which is splined to the input shaft. The clutch disc has friction material where it contacts the flywheel and the clutch pressure plate. Torsion springs on the clutch disc help absorb the engine torque pulses. The clutch pressure plate applies pressure to the clutch disc, holding it tightly against the surface of the flywheel.
In the engaged position, the diaphragm spring holds the clutch pressure plate against the clutch disc, so that engine torque is transmitted to the input shaft. When the clutch pedal is depressed, the clutch release hub and bearing pushes the diaphragm spring center toward the flywheel. The diaphragm spring pivots at the fulcrum, relieving the load on the clutch pressure plate. Steel spring straps riveted to the clutch pressure plate cover pull the clutch pressure plate from the clutch disc, disengaging the engine torque from the transaxle and enabling the gears to be changed.
-----------------------------------------------------------------------------------------------------
Inspection and Verification - MTX-75
The following checks should be carried out before repairing or replacing the transaxle:
Poor gear shifting
  1. Check the operation of the clutch: Lay a block of wood approx. 25 mm thick under the clutch pedal and depress the clutch pedal as far as the stop. If 1st or 2nd gear can be selected with no problem with the engine running and the parking brake applied, the clutch is OK. If the gear cannot be selected, repair the clutch.
  1. Check the selector mechanism:
    • The free play in the gearshift lever must be no more than 15 mm.
      • If the gearshift lever free play is too great, check the gearshift cables and replace them if necessary.
    • If the gearshift lever free play is OK, adjust the gearshift linkage. For additional information, refer to Section 308-06 .
  1. Check the transaxle fluid level and top up with Automatic Transmission Fluid ESD-M2C186-A if necessary.
--------------------------------------------------------------------------------------------------------------------------------------

Dec 21, 2010 | 1998 Ford Contour

1 Answer

How to fit a new clutch into a ford escort 1300cc 1994


1991-96 Models
See Figures 1, 2 and 3
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the transaxle assembly.
  4. If the clutch assembly is to be reused, matchmark the pressure plate and the flywheel so they can be assembled in the same position.
  5. Install flywheel holding tool T84P-6375-A or equivalent, in a transaxle mounting hole on the engine and engage the tooth of the holding tool into the flywheel ring gear.



0900c1528008df86.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Install a flywheel holding tool in a transaxle mounting hole on the engine, and engage the tooth of the tool into the flywheel ring gear
  1. Loosen the pressure plate-to-flywheel retaining bolts one turn at a time, in a crisscross pattern, until the spring tension is relieved, to prevent pressure plate cover distortion.
  2. Support the pressure plate and unfasten the retaining bolts. Remove the pressure plate and clutch disc from the flywheel.

If the flywheel shows any signs of overheating (blue discoloration) or if it is badly grooved or scored, it should be refaced or replaced.
  1. Inspect the flywheel, clutch disc, pressure plate, release bearing, pilot bearing and the clutch fork for wear. Replace parts as needed.

To install:
  1. If removed, install a new pilot bearing using a suitable installation tool.
  2. If removed, install the flywheel. Make sure the flywheel and crankshaft flange mating surfaces are clean. Tighten the flywheel retaining bolts to 71-76 ft. lbs. (96-103 Nm) on the 1.8L engine or 54-67 ft. lbs. (73-91 Nm) on the 1.9L engine.
  3. Clean the pressure plate and flywheel surfaces thoroughly. Position the clutch disc and pressure plate into the installed position and support them with a dummy shaft or clutch aligning tool. If the clutch assembly is being reused, align the matchmarks that were made during the removal procedure.
  4. Install the pressure plate-to-flywheel retaining bolts. Tighten the bolts in the correct sequence to 13-20 ft. lbs. (18-26 Nm). Remove the alignment tool.



0900c1528008df87.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Position the clutch disc and pressure plate into the installed position and support them with a clutch aligning tool


0900c1528008df88.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Tighten the pressure plate-to-flywheel retaining bolts to specification in the sequence illustrated
  1. If the release bearing was removed, lubricate the release fork where it contacts the bearing and install the bearing in the fork.
  2. Install the transaxle assembly.
  3. Lower the vehicle.
  4. Bleed the hydraulic clutch system, if needed.
  5. Connect the negative battery cable.
  6. Road test the vehicle and check the clutch for proper operation.

Sep 30, 2009 | 1994 Ford Escort

1 Answer

Wanting to replace the clutch because it is slipping.


Hope this helps. Best of luck to you!
Greg

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the transaxle.
  4. Gradually loosen the clutch pressure plate bolts, in a crisscross pattern. Support the pressure plate and remove the bolts. Remove the pressure plate and clutch disc.
  5. Inspect the pilot bearing. If it is worn or damaged and does not turn easily by hand, remove it using a puller/slide hammer.
  6. Check the flywheel surface for scoring, cracks or burning and machine or replace, as necessary.
  7. Install a flywheel holder to keep the flywheel from turning. Loosen the flywheel bolts evenly and gradually in a crisscross pattern. Remove the flywheel.
  8. Inspect the clutch release bearing for wear. Replace it if it sticks or does not turn easily.
  9. Inspect the release fork for wear or damage and replace as necessary.
To install: 7923kg32.gif Structural view of the hydraulic clutch system
7923kg33.gif Exploded view of the clutch assembly
Click to Enlarge
7923kg34.gif Flywheel tightening sequence
7923kg35.gif Pressure plate tightening sequence

  1. Lubricate the release fork fingers and pivot with molybdenum grease and install in the release fork boot.
  2. Install the clutch release bearing on the release fork.
  3. Install a new pilot bearing in the flywheel, if removed.
  4. Be sure the flywheel mounting surface and the crankshaft or eccentric shaft mounting surfaces are clean. Remove any old sealant from the flywheel bolt hole threads and the flywheel bolts.
  5. Install the flywheel.
  6. Apply sealant to the flywheel bolt threads and install them hand-tight. Install the flywheel holding tool. Tighten the bolts, in a crisscross pattern, to 71–76 ft. lbs. (96–103 Nm).
  7. Apply a small amount of molybdenum grease to the clutch disc splines and install the clutch disc on the flywheel, spring side toward the transaxle. Install a suitable alignment tool in the pilot bearing to position the clutch disc.
  8. Install the clutch pressure plate, aligning the dowel holes with the flywheel dowels.
  9. Install the pressure plate bolts and gradually tighten, in a crisscross pattern to 20 ft. lbs. (26 Nm). Remove the alignment tool.
  10. Install the transaxle.

May 20, 2009 | 2004 Kia Rio

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond


Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
PARTS ASSEMBLY:
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...