Question about 1999 Toyota Corolla

1 Answer

Footbrake on r/h rear wheel on 1999 corolla not operating at enough pressure. changed brake shoes and wheel cylinder and bled out the system

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 678 Answers

Is the wheel still able to be spun with it off the ground and the brake applied? If that's the case check all the other wheels. It's possible that one part of the master cylinder is bad and could cause both wheels on the same axle to not brake or diagonal wheels to not brake.

Posted on Oct 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the brakes in my 99 Toyota Corolla? I have no brakes and the pedal goes right to the floor.


have you adjusted the rear brakes correctly ( drum brakes)
if not drums then you have air in the systems still
brake bleeding is done starting at the wheel with the longest line and ending at the shortest line
It is a 2 person operation unless you have a pressure bleeder pump attached to the reservoir
your problem is air in the system

Jan 07, 2016 | 1999 Toyota Corolla

1 Answer

Brake pedal


Did you ensure that the master brake cylinder was topped up properly whilst you bled the back brake shoes?

If you did so and the brakes are free of air in the lines, then you still have to adjust the brake shoes to their operating position. Secure vehicle from movement. Jack back wheels of the ground, support with jack stands. Remove the rubber grommets that covers brake adjustment wheels. Turn star wheel adjuster with special adjustment tool or a wide blade screw driver. Lock the wheels with the adjustments, push in brake pedal until you have pressure, back off adjustments until wheel runs freely. you should have plenty of pedal now. Make sure master is at the right level at all times.

If you don't have pedal now then I would suggest you still have air in the brake lines.. If you pump the brakes until you have pressure and the pedal feels spongy , then you still have air in the line somewhere. Bleed until air is removed.

Mar 21, 2014 | Isuzu Rodeo Cars & Trucks

1 Answer

Brake problem


try adjusting the rear brakes up correctly
the spring that holds the shoes together pushes all the brake fluid back into the reservoir and each application has to move the shoes back into contact with the drum
that is enough to get the pedal close to the floor

Apr 01, 2017 | 1997 Chevrolet S-10 Pickup

1 Answer

99 potiac grand am no brake pressure


What order did you replace the items in

Apr 26, 2013 | 1999 Pontiac Grand Am GT

1 Answer

1999 Ford E350 van problem: brake pedal is soft; have replaced master cylinder, rear wheel cylinders, rear brake shoes and drums, front calipers, rotors and discs; have bled master cylinder before...


Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them.

Feb 23, 2011 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

I have re/re the rear brake cylinders,shoes,drums,front rotors,pads,and callipers on my 2000 gmc safari van.i have bled all the brakes. but the drivers front has no pressure or fluid.the other three brakes...


make sure you are bleeding them by doing them as an abs system,do the right rear then the left front,then the left rear then the right front,the opposite wheels are how the system brakes.

Jan 21, 2010 | 2000 GMC Safari

2 Answers

Spongy brake pedal even after ABS bleed and base brake bleed.


Did you adjust the rear shoes out? If the rear drum brakes are out of adjustment they will give you a lot of pedal travel. If the pads are worn have no fear of that U-CLIP brake spring, just change one shoe at a time. Take the spring off one side, change the shoe, put the spring back on the post and do the same to the other shoe, no problem.

Dec 03, 2009 | 2001 Chevrolet Venture

1 Answer

89 c1500, full pedal on brakes until started then goes to floor. Bled system,replaced master cylinder and anti-lock system,now has better pedal but code 4 on brake lite that won't go out. Have replaced...


adjust your rear shoes up so that the rear drums just turn, with them ajusted to a low setting the brake pedal will be low .
also when you start your engine it is noral for the pedal to drop because of the boster ! [ but not to the floor ]
Bruce Pike

Oct 10, 2009 | 1989 Chevrolet C1500

Not finding what you are looking for?
1999 Toyota Corolla Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...