Question about 1995 Jeep Cherokee

Open Question

Re 95 jeep cherokee, small pzieo mounted above brake pedal, used to sound when starting but then came on one day and ran intermitantly until i disconnected, 2 wire plug in, no probs since unplugging, thnx for your help

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 475 Answers

SOURCE: 1989 Jeep Cherokee - Electrical Problem - horn, brake lights, blinkers, radio/cd...

There could be a fusible link under the hood off the starter relay that is burnt out.

Posted on Oct 13, 2008

  • 41 Answers

SOURCE: engine code 95 jeep grand cherokee lerado

12 is a battery disconnect within the last 50 start cycles and 55 means the end of the diagnostic cycle.  Basically the computer found nothing wrong. The 12 code may seem incorrect if you haven't disconnected the battery recently, but from my experience the 12 code shows up almost all the time regardless.

Posted on Dec 16, 2008

  • 3433 Answers

SOURCE: My Jeep Cherokee 95 Radiator temperature is always hot

100 degrees f? That is way too cold Either you have the wrong thermostat or it is wide open. 180 degrees is nominal and give you the best performance.. With AC on, expect 190 to 200 degrees. We are talking farhrnheit and not ccelsius, correct?

Posted on Jun 14, 2009

  • 3 Answers

SOURCE: Blower motor 95 jeep Cherokee

Hi Craftsman,
I suffered a similar failure on my little Rover. I think you will find out the resistor on the blower has had it. It is probably similar in theory. The resistor block contains several resistors. As you alter the blower speed, different resistors are used. One of yours has obviously failed. You need to replace the resistor block, which may be located at the back of the engine bay, on the passenger side, under the wiper module. Or you can remove the resistor block and replace the failed resistor - a competent auto-electrician can do this, or advise you how to.

Posted on Jun 30, 2009

  • 6982 Answers

SOURCE: headlight switch on 95 jeep cherokee

Pretty sure there's a nut around the front where the shaft goes in, you may need to remove bottom panel to get your hand behind, then push small button on switch to disengage the shaft.

Posted on Jul 19, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What type of oil do i use in my 1999 jeep grand cherokee limited edition and my brakes sound like air is comming out of the foot pedal when ever i use them...what is messed up so i know what to fix...ty...

Hello Melani,
your jeep calls for either 5w30 or 10w30 oil If you are in colder climates run 5w30 if down south in warmer weather run the 10w30. The air noise you are referring too sounds like you have a power brake booster starting to fail. These are vacuum operated off of the engines vacuum and when you start hearing a sucking sound when pushing on pedal,this indicates the booster is leaking need to have that checked and repaired very soon. Thanks for choosing fixya Melanie and have a great Day

Nov 08, 2011 | 1999 Jeep Grand Cherokee

2 Answers

My brake light wont come on and i look at every fuse could it be a relay problem

Replace brake light switch. It's mounted just above brake pedal under dash

Apr 06, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Which wire in my 99 jeep cherokee sports hatch powers the break light?

Before chasing wires, I'd start looking at brake light switch. (I'm assuming you don't have brake lights) Brake light switches are a common problem - it's mounted just above your brake pedal under dash - small switch w/a couple of wires coming from it. Easy fix

Mar 28, 2011 | Jeep Cherokee Cars & Trucks

2 Answers

My 1994 jeep cherokee has the break lights on when is shut off

If you mean the rears brake lights, you more than likely have a bad or mis-adjusted brake light switch. It's tough to get at. Located on the upper side of the brake pedal arm, under the dash.

Feb 18, 2011 | 2004 Jeep Grand Cherokee

2 Answers

Every time i turn off my 98 Jeep Cherokee, the brake lights stay on until i step on the brake. Then they turn off. Is this normal or is something not right?

It is not normal. I would say your break switch is sticking. There is a button on the end that sometimes gets stuck. It turns your brake lights on and off.

Feb 06, 2011 | 1998 Jeep Cherokee

1 Answer

95 jeep cherokee no brake lites bulbs o.k.

check the brake switch on top back side of brake pedal. it is out of adjustment or is going bad. if bad or out of adjustment, brake lights will not work. adjust the brake switch.

Oct 17, 2009 | 1995 Jeep Grand Cherokee

1 Answer

My 1998 jeep cherokee has a lighting problem. The

wiring under dash chauffed through by brake pedal

Jun 03, 2009 | 1998 Jeep Cherokee

1 Answer

2000 Jeep Grand Cherokee brakes make a hissing noise

has your brake pedal seem to be stiffer than usual? the sound you hear is from the brake booster if it has a leak it will cause a noise but you would have a stiffer pedal because the booster is loosing vacuum.

Feb 08, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Cherokee Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides