Question about 1996 Ford Explorer

2 Answers

Was running fine went in store will not crank not getting gas checked fuses and will hit on stater fluide but not getting gas is tere a relay or just the pump

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 21 Answers

Check your battery cable at the battery and at the starter they corroade
run jumper cable from +post to starter if it starts need to replace cable

Posted on Oct 06, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 90 Answers

There is one thing you need to check, it is called the inertia switch. it is a little black box with a red button on the top of it. common problem for fords. if the switch gets bumped it cuts of the fuel to the motor for safety in the event of an accident. They are usually located down on either the passanger side or drivers side floor behind the panel that would be by your right foot if you are sitting in the pass seat. if it is not in the front then check in the rear like in the area inside where the jack gets stored.

Good luck and I hope this Helps. Allen

Posted on Oct 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I think that I ran my 16la new holland out of fuel so I put some more in. after loosening some bolts , i turn key and nothing . Could stater have went bad or a fuse ? Didn't crank a lot at All


Try this turn key to run do not try to start if you ran out of gas need to prime engine. Wait a couple!minute then try to start. Also check fuses. If starter went bad engine will not crank only hear a clicking noise

May 02, 2016 | Cars & Trucks

3 Answers

I brought a camshaft sensor for my gmc 2005 envoy an it still want crank turns over fine but want start what could it be..


Could be many things. Run tests such as fuel pressure test (many parts stores will loan you a test gauge if you don't have one). If you are such you don't have spark to plugs, get ignition module tested (most parts stores do this free) test coil(s), test cranks sensor, reset theft deterrent if needed.

Feb 21, 2016 | GMC Cars & Trucks

1 Answer

2000 ford expedition 5.4 litter 4x4 Eddie baur with air suspension starting problems sometimes it will start now it won't start at all it cranks .


IF IT WILL RUN WITH STATER FLUID YOU HAVE A FUEL ISSUE. SINCE PUMP SOUNDS DIFFERENT I WOULD START THERE. CHECK FOR VOLUME & PRESSURE ON FUEL RAIL IF IT NOES NOT THEN THE PROBLEM IS IGNITON, CHECK FOR SPARK

Jan 05, 2015 | Ford Cars & Trucks

1 Answer

1991 ford tempo ran fine went to store it started fine and then just died


Likely a gas or spark problem. Spray starting fluid into the air intake while cranking it. If it then runs for a few seconds, it's a fuel problem-maybe the fuel pump, filter, or injector circuit. Check if gas is getting up to the engine.
Buy an inexpensive "spark tester" at a parts store, and check for spark- if no spark, the ignition circuit will need diagnosed- could be the ignition coil, maybe the electronic ignition module-several possibi9lities. Let me know what you find, or if other questions..

Feb 16, 2014 | Ford Tempo Cars & Trucks

1 Answer

97 mercury mountaineer. won't start


hi,

watch your oil pressure when cranking, you have to have some oil pressure to get the fuel system to start. you may have to find the hot wire at the relay and energize it to see if it is indeed the fuel pump going out. if its been sitting and its a 97 the fuel pump just might have went, you can also try hitting the gas tank from the outside in the middle to see if that works too. have a water hose or fire extinguisher around when your working on fuel system and leave one of your battery cable a little loose..

jm

Jul 04, 2017 | 1997 Mercury Mountaineer

1 Answer

Drove the car to the store and it was fine, came home, my son started checking fuses and then went to start the car and it wouldnt start......we replaced the gas filter and the battery.....checked all the...


As the problem started when your son had a look at the fuses, I'd suggest you check them yourself. Make sure they're good and in the correct slots.

May 11, 2011 | 1998 Nissan 200SX

1 Answer

The car was running fine we drove it to the grocery store and came out it would not start put gas in it and it started-got it home shut it off went to crank it and it would not start-added more gas to it...


Believe your fuel pump is bad when you first turn on your ignition (don't try to start car) do you hear a clicking or humming noise? If not you fuel pump may not be working also check fuel pump fuse and relay check owners manual for locations.

Jan 06, 2011 | 1989 Jaguar XJ6

1 Answer

93 gmc sierra 5.7 liter engine, injection carb, will turn over won't start, replaced fuel pump fuse, replaced fuel pump relay, replaced fuel pump inside gas tank, no gas flow to carb , gas gauge has always...


you say you replaced the fuse, but does the fuse have power? the gray wire at pump should have power when cranking, or for 2 seconds when turning key on. At fuel pump relay, put power onto gray wire, the pump should run if the wiring is good. if it doenst run then ck for power at fuse while power is on gray wire.

Oct 19, 2009 | 1995 GMC Sierra C1500

1 Answer

Starting problem


have your battery load tested at parts store


shack

Apr 18, 2009 | Dodge Ram 3500 Cars & Trucks

Not finding what you are looking for?
1996 Ford Explorer Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...