Question about 2006 Jeep Liberty

1 Answer

Replaced starter 2006 jeep liberty still won't turn over 3.7 engine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 454 Answers

Check that you have power at the main post of the starter. Then check the solenoid activation circuit from the ignition switch.

Posted on Oct 04, 2009

Testimonial: "have power at post on starter-could it be safety neutral switch on transmission?"

  • David Jewell Oct 04, 2009

    You can do a continuity test with a voltmeter to check if it is the neutral safety switch. Do you have an electrical shematic showing the starting system?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the position of radiator fan relay on jeep liberty 2006


no idea to be honest earlier jeeps had then at the front of the wing down below as i remember ?? newer one would i imagine be in the electrical box under the bonnet near the battery

Dec 02, 2016 | Jeep Cars & Trucks

1 Answer

How do I remove the starter motor on a jeep liberty 2005/2006 crd


there are 3 engines, are we to guess that?
2.4 ,3.7 and 2.8Liter
what trouble, you didnt say?
can reach it.
cant turn it
its at an angle (use a universal joint , on socket driver?)

show a photo ? so we can all see the deal there.
some cars have shields (heat) did you find that and remove that?


ill do wild guessing, 3.7L
step 3 in the FSM. (alldata.com)
  1. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
did you skip step 1,
disconnect battery neg lug?>
Do so or risk eating acid for breakfast....... or worse.

Oct 07, 2015 | 2005 Jeep Liberty

1 Answer

2003 Jeep Liberty- Starter is turning, but eng won't start (intermittent problem)


Battery could be weak. Not enough current to keep the engine firing. If battery is more than 3 years old then replace it. Other thing could be the fuel injector. Maybe need cleaning. Use injector cleaner additive in fuel. Get the right type for your engine and follow instructions on container.

Sep 02, 2014 | 2003 Jeep Liberty

1 Answer

2006 jeep liberty rear lift glass won;t close


Mine did this too....the latch kept getting stuck. If you put the key in the ignition and unlock the power doors, pull on the gate door (don't open it, just enough to release the latch), and it should come out so the hatch will latch.

Feb 18, 2013 | 2006 Jeep Liberty

1 Answer

My 2006 jeep liberty won't supply fuel


check the fuel pump,fuel filter or the fuel fuse

Oct 13, 2012 | 2006 Jeep Liberty

1 Answer

My 2006 Jeep Liberty won't start or turn over all I keep hearing is this click sound when I turn the ignition , Plus I just replaced the battery........What shall I check next?


check your starter,better yet has your alarm system been activated and possibly shut down your car a passive alarm will do that

Mar 27, 2012 | 2006 Jeep Liberty Limited

2 Answers

Hi my 2006 Jeep Liberty won't start or turn over all keep hearing is this click sound when I turn the ignition , Plus I just replaced the battery .


Probably a starter. It sounds like the starter solenoid is working, but the starter motor is not energizing.

You could try this simple trick, but Im about 85% sure you have a bad starter.

Have a buddy help you push the vehicle in neutral for a short distance. When you get it moving at a walking pace, put the transmission in Drive, and let the vehicle come to a stop. You may hear a little clicking, but thats OK, it wont hurt anything. Put the transmission back in Park and try to start the engine again. Sometimes the starter gear gets stuck on the flywheel and it wont engage when you try to start the engine. This trick may move the flywheel a little so the starter can engage.

Mar 27, 2012 | 2006 Jeep Liberty

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

1 Answer

Jeep Liberty Diesel will not turn over. Battery charged. Cannot get diagnostic codes from the computer.


try it in nutral put in park and hold up and or jigle up and down in park, dont come out of park jiggle while u hold to start,check large fuses anything marked starter check cables cable ground to engine ,check nutral safty switch check starter , and starter wire ing wire at starter with test light small wire on starter while someone trys to start jeep ground test light to a good ground and hold point on small wire on starter it should light up if it does your starter is bad ,if it doesnt light up check ignition switch on steering colum ,most likely bad

Jun 27, 2009 | 2006 Jeep Liberty

Not finding what you are looking for?
2006 Jeep Liberty Logo

Related Topics:

678 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...