Question about 1992 Jeep Wrangler

2 Answers

I need to bleed the clutch on my 1992 jeep wrangler and need to know were to locate the bleeder insert

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,077 Answers

The bleeder valve will be on the slave cylinder. Follow the hydraulic line from the Master Clutch cylinder down to the slave cylinder by the transmission.

Posted on Oct 04, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The bleeder valve should be on the passenger side of the transmission if you have a 4 cylnder and drivers side for a 6. make sure you use a vacuum system when bleeding or bleed several times, as air tends to stay in the top of the slave because of its design.

Posted on Mar 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 jeep wrangler bleed slave cylinder


You need to do this with a vacuum bleeder like those made by MITYVAC, they cost about $30 and are available at most better auto parts stores and some retailers like Walmart (not sure on that). The tool comes with full instructions and adapters for most clutch bleeder ports.

Jul 13, 2012 | 1991 Jeep Wrangler

1 Answer

I need to bleed the clutch slave cylinder but just not sure if I am loosening the right part. Can't find any pictures.


There is only one bleeder valve on the clutch slave cylinder so you can't be loosening the wrong part if you're opening the bleeder valve on the slave cylinder.

Sep 18, 2011 | 1992 Jeep Wrangler

1 Answer

Where do you bleed the clutch at on a 1997 jeep wrangler what is the location of it


This all depends if this is a hydraulic clutch or if its cable operated, you can only bleed hydraulic clutches, to bleed it you would bleed at the ******, you will see the bleeder screw on the slave cylinder that operates the clutch fork.

Sep 03, 2011 | 1991 Jeep Wrangler

1 Answer

Looking for a diagram for a 1999 Jeep Wrangler Sahara that shows photos on how to find the bleeder screw on bleeding the clutch


You wont need a photo its super easy, but it is under the jeep follow the line from resivior to the clutch master cylinder (holds fluid) then the other end located on the trannsmission is the slave cylinder the bleeder is on it usually has a rubber cap on it! hope this helps. p.s. dont let the resivoir get empty it will leave air in the system and make bleeding almost impossible.

Aug 17, 2010 | 1999 Jeep Wrangler

1 Answer

How do you do you bleed a clutch line on a 1993 jeep wrangler?


Just like you would bleed brakes. Fill the reservior with brake fluid, open the bleeder screw and have a friend press the clutch pedal in. Close the bleeder screw and let up on the clutch. Do that until the clutch pedal has a good feel. Be sure to check the reservoir frequently as they don't hold much fluid and if you let it get low you'll **** more air into the system.

Jul 31, 2010 | 1993 Jeep Wrangler

1 Answer

Looking for picture of clutch bleed valve


on the drivers side of the bellhousing the bleeder valve it located on top of the clutch slave cylinder

Jan 21, 2010 | 1991 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

1 Answer

How do i bleed the clutch slave cylinder on a 95 jeep wrangler


pump up clutch pedal really fast about ten times....leave it held to floor....open bleeder on slave cyl... repeat untill you have good pedal....may need to adjust master cyl. rod on clutch pedal to get more travel....good luck....Lee

Nov 06, 2009 | 1995 Jeep Wrangler

3 Answers

How do I bleed hydraulic clutch in 1991 jeep wrangler


There is a bleeder on the drivers side of the transmission follow the tube from the clutch master cylinder if you cannot find it. Pump the clutch up and hold it down then open the bleeder repeat till air is gone. May have to bleed again after driving a bit. If you want to bleed the clutch master cylinder run a tube from where the line goes into the cylinder and take the cap off and run the tube into the fluid (make sure its in the fluid) then pump the clutch slowly until no air bubbles. I just replaced my clutch master cylinder this is where the information comes from hope it helps you out!

Mar 04, 2009 | 1991 Jeep Wrangler

3 Answers

1990 jeep wranger slave cyclinder


The clutch slave cylinder on this model is located inside the transmission bell housing. You would have to pull the tranny to see it.
Bleeding the slave cylinder is a fairly simple process.
Underneath the vehicle on the driver side you will see two hydraulic lines going into the transmission where the tranny connects to the engine. If you have trouble locating just follow the hydraulic line from the master cylinder on the firewall.
One of these lines is actually sticking out of the tranny and has a bleeder valve on the end.
You will need a 9/16 box end wrench and a 5/16 or 1/4 inch box end wrench and someone with you to press the clutch pedal while you are under the vehicle.

1. Top off the master cylinder with clean brake fluid. Also, MAKE SURE you keep the fluid level in the master cylinder topped off during this process. You may need to have a second helper to take care of this so you don't have to keep climbing out from underneath.

2.Hold the line with the 9/16 and loosen the bleeder valve a couple turns or until fluid begins to drain. Have someone SLOWLY depress the clutch pedal to the floor and hold it down to the floor until you tighten the bleeder valve back up. MAKE SURE YOU ARE OUT OF THE WAY OF THE SQUIRTING FLUID WHEN THE PEDAL IS DEPRESSED!!

3. Once you are sure the valve is tight, have them pump the clutch pedal a couple times . Repeat step two until the pedal has a full stroke.

Jan 02, 2009 | 1990 Jeep Wrangler

Not finding what you are looking for?
1992 Jeep Wrangler Logo

648 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...