Question about 2004 Ford Taurus

1 Answer

No communication to the wheel sensors on 2004 Ford

No communication to any of the wheel sensors on 2004 Ford Taurus.
Is there an internet site to get an ABS module for this that is cheaper than the dealer?

Posted by on

  • rcfeathers Oct 04, 2009

    CORRECTION: The ABS control module on my daughter's 2000 Ford Taurus is not communicating with any of the 4 wheel sensors. Is there anyplace online to purchase a new ABS control module for this car?

  • lexbev May 11, 2010

    did you put aftermarket wheels on?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 194 Answers

Ford and GM often permanently "marry" the electronic and hydraulic portions of the module making rebuild more difficult as the 2 halves require a different procedures and skillsets to repair (1 is a computer board with chips and circuits, 1 is a hydraulic pump and mechanical valve assembly with some solenoids). You can try BBA-REMAN.COM, they may be able to rebuild it for you, but the majority of rebuilders out there prefer to stick with electronic only rebuilds (Typically european cars all use bosch style seperateable units available as exchange at many rebuilder shops). You may end up with faster luck trying to locate a used unit at a local junkyard that offers say a 30 day guarantee.

Have you verified that the wheel signals are in fact present and are reaching the module? Wheel speed is calculated seperately for each wheel, and processed seperately. It is rare (though not unheard of) for a module to fail in a manner that disables all sensors at once. Typically a module that has lost ability to process a signal or is grounding a signal internally will affect only 1 or 2, and the others will continue to function normally. Also solder cracks on the board are not uncommon, though again that would be very rare to affect all 4 at once.

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 ford taurus won't it turn, why does it act as if it was stuck on gear?


Hi sounds if you have sticking brakes jack up wheels make sure all wheels turn freeley.cheers Ron.

Jun 28, 2014 | 2004 Ford Taurus

1 Answer

2004 ford taurus turn signals don't turn off when steering wheel turns straight again


There is a cam assembly inside the steering wheel. It is not too easy to get to and wears out too quickly.

Mar 30, 2013 | 2004 Ford Taurus

1 Answer

Code B1155 for ford taurus


its abs code could be a wheels sensor or maybe the wire broke lots of time the sensor gets dirt or rust and cant read the teeth on the wheel hub. try taking sensor out and cleaning them see what happens.

Feb 27, 2013 | 2002 Ford Taurus

1 Answer

How to change a rear wheel bearing on a 2004 ford taurus???


How to Replace Rear Wheel Bearing/Hub Assembly on a 2nd generation Taurus

The following procedure is for a Ford Taurus (VIN S), with rear drum brakes and ABS.

1. Loosen wheel lug nuts, raise rear of vehicle, and support securely on jack stands. Block front wheels and remove rear wheels.

2. Remove brake drum (parking brake must be off).

3. Remove and clean ABS Sensor (Torx E8) with a spritzled rag.

4. Remove grease cap from hub.

5. Remove and discard hub retaining nut (36 mm). This is a compound nut, comprised of several nuts inside a metal cage. Use a 36 mm axle nut socket (e.g., OEM 25206). Many auto parts stores will lend you this socket. A 1/2-inch drive air impact wrench or breaker bar is necessary to remove the nut.

6. Remove wheel bearing/hub assembly from spindle. It easily comes off by hand.

7. Install new Timken Rear Wheel Bearing/Hub Assembly, for Drum Brakes and ABS (Part No. 512162). Tighten new axle spindle nut (Dorman 05114) 221 lb.-ft., replace grease cap, and button everything up.

Jun 22, 2012 | 2004 Ford Taurus

1 Answer

Changing throttle position sensor on a 2004


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the throttle position (TP) sensor electrical connector.
  3. Remove the screws and the TP sensor.

923d1f7.gif
Throttle position (TP) sensor electrical connector


b3a94a2.gif
TP sensor


To install:
  1. Install the screws and the TP sensor. Tighten screws to 7 inch lbs. (3 Nm)
  2. Connect the throttle position (TP) sensor electrical connector.
  3. Connect the battery ground cable.

Apr 25, 2010 | 2004 Ford Taurus

Not finding what you are looking for?
2004 Ford Taurus Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...