Question about 1996 Chevrolet S-10 Pickup

1 Answer

Clutch sleeve I need to know how to bleed the hydralic clutch sleeve and change the oil in the sleeve on a 1996 chevy s-10 pick up truck

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,068 Answers

I just did one of these t the shop and they are very hard to do. system is difficult to work on and the slave cyinder is inside the transmission so i would tread carefully on this one if you are ot sure of what you are doing.

now if you are trying to flush the fluid the best way is to keep the cap off the master cylinder and keep the level up because if you let it run dry it will get air bound and when you open the bleeder it will come out very quickly. now the bleeder is on the drivers side of the transmission right above the hydraulic line going into the slave cylinder. have someone up top to keep adding fluid and someone under the truck to open and close the bleeder. when you have the bleeder open let the fluid run out until it looks clear like the new fluid you are putting in! tighten bleeder but not over tight and thats about it.

the bleeder screw is a 11mm and that's all you will need for tools!

if your pedal is soft when you try to use the clutch after doing this it is recommended by the manufacture when preforming a bleed of the system to pump pedal several times until it comes back up and to keep doing this until it is back up.

good luck

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How remove and replace clutch slave cylinder 1996 acura integra


10 mm line wrench and a 12 mm wrench or socket. Takes 2 people to bleed it. Look at your master cylinder inside the cabin, they leak too. Most people recommend replacing both at the same time. On a car this old, you might replace the rubber hydralic line too.

Jun 19, 2014 | 1996 Acura Integra GS-R

1 Answer

Toyota hiace first gear very hard when changing


hi it can be the clutch is not totaly disengageing i dont know the year of your hi ace check the hydralic oil for the clutch or if its a very old truck the clutch cable can also be syncronizers 1gear or no gear oil in trans" newer models use atf oil

Nov 28, 2013 | Toyota HiAce Cars & Trucks

1 Answer

How to bleed a hydralic clutch on a 2001 chevy blazer


You must reverse bleed it. Go here to learn how. You will need to buy the tool pictured.

Dec 05, 2012 | 2001 Chevrolet Blazer

2 Answers

My 1996 Chevrolet K3500 Dually has a hydraulic clutch, how do I change the fluid and bleed it.


FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Jan 22, 2011 | 1996 Chevrolet C/K 3500

1 Answer

When I step on the clotch it gets stuck and dosent come back out


CHECK CLUTCH MASTER CYLINDER.SOUND LIKE BRAKE FLUID LOW.IF BRAKE FLUID LOW LOOK FOR LEAKS AROUND CLUTCH MASTER CYLINDER AND CHECK FOR LEAKS AROUND BRAKE LINES AND CHECK FOR LEAKS AROUND CLUTCH RELEASE CYLINDER HYDRALIC LINE FITTING. REASON PEDAL GOING TO FLOOR YOU HAVE FLUID LEAK WHICH WILL CAUSE AIR TO GET IN THE CLUTCH HYDRALIC SYSTEM. YOU HAVE TO LOCATE LEAK FIX AND BLEED THE CLUTCH HYDRALIC SYSTEM.

Dec 27, 2010 | 1999 Volkswagen Passat

1 Answer

Need to bleed the hydralic clutch system on a 1993 chevy 2500 trk .Replaced old line,now need to bleed the rest of the air out


Should be a bleeder on the slave cylinder. remove the cover on the master and open the slave and let drip until fluid drops sdteady and no sign of air. Close slave and close master after replenishing the fluid. The first time you press on the pedal go slow and release real slow. Then you are off and clutching. Good Luck

Jul 19, 2009 | 1993 Chevrolet C2500

4 Answers

Grinding when engaging into gear when warmed up.


ok every time you open the clutch resevoir you have to bleed the slave ..next hold down the clutch to the floor open the bleeder screw 10 mm bolt and then close it and pick the pedal up off the floor if your clutch is not right the pressure plate is failing most likely on mitstu stuff ...bleed first ..

May 08, 2009 | 1990 Eagle Talon

1 Answer

94 jeep pick up can't get the hydralic clutch bleed


need to free flow, means to open bleed valve open and let it run down but adding fluid to till you dont see air bubbles.
use a clear pice a hose, hook it to bleeding valve and into a bottle with 1/4 full of fluid will take few tries.

Feb 15, 2009 | 1991 Jeep Wrangler

2 Answers

95 mazda b4000 slave cylinder bleeder valve location


the nipple sticks out side the bell housing on the left side just above your hydralic line for your clutch,auto zones web has a complete diagraham and steps for bleeding

Jun 17, 2008 | 1996 Mazda Pickup

Not finding what you are looking for?
1996 Chevrolet S-10 Pickup Logo

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...