Question about 1994 Mazda 323

2 Answers

Need to change cv outer boot on mazda ba 94 model.

I am trying to change the cv outer boot. do i need to disconnect the whole steering rack from engine. please tell me easiest way to change boot.i have already taken off wheel and disconnected hub exposing the cv joint but i am stuck at this time.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 4,369 Answers

It just pulls out. it hasa circlip that holds it in on driver side. which side?

here's an escort, should be similar. note step 17

Removal

  1. Raise and support the vehicle.
  1. Remove the lug nuts (1012) and the front wheel and tire assembly.
  1. Remove the front fender splash shield bolts and the front fender splash shields (16103) .
  1. Use a small cape chisel to carefully raise the staked portion of the front axle wheel hub retainer (3B477).




  1. Remove the front axle wheel hub retainer and discard it.
  1. Remove the cotter pin and the tie rod end nut from the tie rod end (3A130). Discard the cotter pin.




  1. Use an appropriate tie rod end remover to separate the tie rod end from the front wheel knuckle (3K186).




  1. Remove the ball joint bolt and the ball joint bolt nut.




  1. Carefully pry down on the front suspension lower arm (3078) to separate the front suspension lower arm ball joint (3050) from the front wheel knuckle.




  1. Pull outward on the front wheel knuckle (3K185). Carefully pull the front wheel driveshaft and joint from the front wheel knuckle and position it aside.




  1. NOTE: Removal of the LH front wheel driveshaft and joint (3B437) requires removal of the transmission support crossmember (6A023) to allow access with a pry bar. If the LH front wheel driveshaft and joint is being removed, continue with step 11. If the RH front wheel driveshaft and joint is being removed, continue with step 15.

    Support the transaxle with a transaxle jack or equivalent.
  1. Remove the four transaxle mount-to-rear engine support nuts.




  1. Remove the two rear engine support nuts at the rear of the transmission support crossmember.
  1. While supporting the rear of the transmission support crossmember remove the two rear engine support bolts. Remove the transmission support crossmember.




  1. Position a drain pan under the transaxle.
  1. Insert a pry bar between the front wheel driveshaft and joint and the transaxle case.
  1. need to change cv outer boot on mazda ba 94 model. - stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Extreme care must be taken to ensure that the pry bar does not damage the transaxle case, the transaxle oil seal, the front wheel driveshaft and joint, or the front wheel driveshaft joint boot (3A331).
    Gently pry outward to release the front wheel driveshaft and joint from the differential side gears (4236).




  1. Remove the front wheel driveshaft and joint.




  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When the LH and RH front wheel driveshaft and joint assemblies are removed, Transaxle Plugs T88C-7025-AH must be inserted to prevent the differential side gears from becoming mispositioned. If the gears become misaligned, the differential will have to be removed from the transaxle to align the gears.
    If both front wheel driveshaft and joints were removed, install Transaxle Plugs T88C-7025-AH in the differential side gears.
  1. Remove and discard the driveshaft bearing retainer circlip (3Z498).

Posted on Oct 03, 2009

Testimonial: "thanks so much for your help. you have saved me heaps"

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Master
  • 302 Answers

Remove cotterpin and nut from end of idler arm then smack side of spindle where idler is connected with a hammer untill arm comes loose, then remove three outer nuts from top of strut at fender under hood,[do not remove large center nut], raise vehicle untill strut falls free and remove cv assy

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need know how get shift out streeling knuckle on 2004 Pontiac Aztek front wheel drive what all tools i need


2004 Aztek: replace the right front steering knuckle - JustAnswer

www.justanswer.com > Car Questions > Pontiac Problems
2004 Aztek: replace the right front steering knuckle - Answered by a verified Pontiac Mechanic.

How do i change a CV Joint on a pontiac aztek - JustAnswer

www.justanswer.com > Car Questions Disconnect the outer tie rod end from the steering knuckle; do NOT loosen the tie rod end jam nut. Refer to Rack and Pinion Outer Tie Rod End Replacement in ...

steering knuckle video for 2004 Pontiac Aztek Google Search

Jun 25, 2017 | Pontiac Cars & Trucks

1 Answer

Diagram cv inner outer mazda sting


Inner cv's hardly ever pack up it is the outer ones as it works harder in turns. it will be a clukking noise and some grinding. Make sure they are well greased and the rubber boots are not torn. if it has wear replace it as it can be costly when it fails.

Dec 03, 2013 | Mazda Cars & Trucks

1 Answer

Change power steering pump


Play in the steering wheel is likely from worn tie rod ends. Have your inner and outer tie rods checked. The outer tie rods are connected to the rod ends coming out of the rack on each side, and are connected to the wheels. The inner tie rods are not visible-but are on the rods under the protective boots on each end of the rack and pinion assembly.
You may need a new rack assembly, but first check if you just need new tie rods.

Nov 25, 2013 | 1997 Honda Accord

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

Change cv boot kit rack and pinion


first you have to remove outer tie rod then you can slide the boot into place then re install the tie rod try not to move jam nut so that your alignment wont change.

Feb 02, 2010 | 1992 Honda Accord

3 Answers

When replacing a outer C.V joint boot , do you


you can replace just the outter but you may want to replace the whole axle alot easier

Jan 17, 2010 | 1993 Ford Festiva

1 Answer

Something knocking in a steering system on my 98 civic


Suspect worn outer cv joint. Check the boot for any tears, damage or leaking grease. If these are present your cv joint will fail soon if it hasn't already. If you put the car into reverse and turn the wheels to a hard lock a bad cv joint will make a popping grinding type sound. Try left and right turns when doing this test.

Sep 17, 2009 | 1996 Honda Civic

3 Answers

Is the cv joint part of the axle assemble on a 2003 volvo s80


Hi,
On the the rear of the car they are part of the axle, on the front of the car the CV joints are connected to the steering rack/rods.
They are located directly behind each wheel like this >>>>>>

3d1dbe9.jpeg


Regards.

Sep 04, 2009 | 2003 Volvo S80

1 Answer

Rack/Bellow Boot Replacement


if you are talking about the steering rack boots, you cam just take a hacksaw and make a small cut right behind the locking nut on the inner tie rod ond shaft. The nut that you need to loosen a bit to take the outer tie rod end off. make a small cut right behind it, so you can see where to stop wit it when you put the whole assemble/boots back on. That would be what I would do, if I didn't want to get it aligned after. It will be close enough, but I would keep an eye on your tires to make sure, they are not wearing off faster than normal. If you talking CV boots, different procedure. Let me know.

Sep 02, 2008 | 1996 Nissan Maxima

2 Answers

When turning hear a clicking noise from drivers front wheel 1999 mazda millena s


most likely the cv boot is bad will need to be replaced recomend change the whole cv axle

Jul 29, 2008 | 2000 Mazda Millenia

Not finding what you are looking for?
1994 Mazda 323 Logo

470 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...