Question about Dodge Dakota

2 Answers

Fuel pump ground location

Fuel pump ground location

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Master
  • 302 Answers

The fuel pump is grounded internally through the wiring harness

Posted on Oct 03, 2009

Testimonial: "Thank you."

  • Ann Philips Jul 24, 2013

    still do not understand where it starts and ends.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Should I be able to hear the fuel pump working when I turn car on 93 dodge caravan

Posted on Jan 04, 2010

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

skychief2001
  • 21873 Answers

SOURCE: 1990 buick riveria fuel pump

The ground wire should be in the harness with the pump feed and the sending unit wire.

Posted on Sep 30, 2012

ajauto57
  • 308 Answers

SOURCE: where is the fuel pump ground wire located ?

sender unit has wire coming off it which is your ground on top of frame towards 1 ft forward to back of tank

Posted on Dec 16, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Chevrolet trail blaser shut off switch location


If your talking about the fuel pump, there is no shut-off switch. If your sure it is the fuel pump, check the fuel pump wiring for voltage and ground, engine cranking. Gray wire is voltage, black is ground. The pcm B fuse is in underhood fuse block. If good voltage and ground at the fuel pump with no fuel pump action or fuel pressure, suspect the fuel pump.
26382285-nrskmkvrvozcbhjjah0si5ae-2-0.jpg

Dec 02, 2016 | Chevrolet Cars & Trucks

1 Answer

Fuel pump relay overheating..tried new fuel pump, relay,repair engine ground..believe it is a loose ground from relay to somewhere, can't find location of ground


The relay grounds are the fuel pump and the ECM. If it over heats, it's because the pump is pulling to many amps. Replace the hot wire to the pump and the ground wire from the pump. One or both will solve your problem.

Aug 02, 2015 | Cars & Trucks

1 Answer

Where is fuel pump relay location 2003 BMW 745 SERIES LI


Hi Greg-
The fuel pump is provided power by the SBSR- right side B-pillar airbag module. You can check for power and ground at the connector of the fuel pump across the 2 larger wires. The brown wire is ground. You should have battery voltage to the connector.

Aug 17, 2014 | BMW 745Li Cars & Trucks

1 Answer

Where is the fuel pump ground wire located ?


sender unit has wire coming off it which is your ground on top of frame towards 1 ft forward to back of tank

Dec 16, 2012 | Cars & Trucks

1 Answer

Fuel Pump location


it is an electronic fuel pump module and it is located in the fuel tank. It is pretty simple to check for fuel pressure with a fuel pressure gauge. There will be a test port on the fuel rail.

If there is no pressure than check for power to the pump as close to the pump as you can and with the pump plugged in. Also check to make sure the fuel pump has good ground. The larger grey wire should be the power wire to the pump. Black is ground.

Jul 24, 2012 | 2007 Chevrolet Uplander

2 Answers

Fuel pump not working


First check the fuel pump relay...It's located underhood junction block, in the left side of engine compartment.

Sep 15, 2011 | 1999 Pontiac Grand Am GT

1 Answer

Fuel pump replacement


How to Replace a Fuel Pump

Parts:
1. Fuel Pump - $51.16

ff89027.jpg

DELPHI, ELECTRIC FUEL PUMP -- Meets Or Exceeds OEM Quality, Matches The Genuine Fit And Function

Tools:
1. 3/8 in. Drive Ratchet
2. Floor Jack
3. Multimeter
4. Jack Stand Set
5. Flat Head Screwdriver
6. Mallet Hammer
7. Socket Set

Steps:
Step 1 * Locate the fuel pump.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 * Have a friend turn the key to the“ON” position while you listen for a high pitched hiss/whine coming from the electric fuel pump.
o Tip: If the fuel pump is located in the fuel tank, you can open the fuel cap and listen to hear the fuel pump. The fuel pump should run (priming the system with fuel) for a couple of seconds. Once it stops, you should be able to start the vehicle.

Step 3 * If the fuel pump does not make a sound (run and prime the fuel system) check to see if there is a fuse that supplies power to the fuel pump and check its location.
o Tip: Check the owner’s manual for location of the fuse box and fuel pump fuse.

Step 4 * Once you have found the location of the fuel pump fuse, remove the fuse from its housing and check to see if it is blown.
o Tip: A blown fuse will usually have a metal strip connecting both tabs that“blows out” (the wire looks as if it has been chopped in half or broken).

Step 5 * If you noticed that the fuse was blown, replace the fuse with a new fuse of the same amperage and repeat step 2.

Step 6 * If the fuel pump now works, you do not need to replace it. However, you will need to find what caused the fuel pump fuse to blow. We strongly recommend that this is done through a certified shop, unless you have the tools and knowledge to test electrical systems and diagnose more in depth problems.

Step 7 * If the fuse wasn’t blown, it should be checked for power and ground at the fuel pump. If there is power and ground present then you will need to replace the fuel pump.
o Tip: On most vehicles you may need to lower the fuel tank to access the power and ground leads for the fuel pump.

Step 8 * Siphon or drain as much fuel as possible from the fuel tank. Disconnect any possible fuel lines from the fuel tank.

Step 9 * Remove any retaining straps or bolts holding the fuel tank to the frame.
o Tip: You may be able to access the fuel pump from the bottom of the back seat or the trunk of the vehicle.

Step 10 * Using a digital multi meter, turn the key to the“ON” position and check for power at the fuel pump. Touch the negative lead from the DMM to a good ground and the positive lead of the DMM to the power cable at the fuel pump. You should have a reading that is equal to battery power. If you do not have a reading at all, you will need to inspect the power side of the fuel pump.
o Tip: With the ground lead of the DMM still connected to a good ground, touch the power lead to the positive side of the battery, to each side of the fuse, and again to the fuel pump. Wherever you notice the voltage reading goes from battery voltage to 0 you will need to replace whatever wires and fuse are in between.

Step 11 * If you have noticed that the power and ground being supplied to the fuel pump are both good, then you will need to replace the fuel pump.
o Tip: To check for a good ground, place the negative lead from the DMM to the ground side of the fuel pump, and the positive lead of the DMM to the positive side of the battery. If the reading on the DMM is battery voltage then you have a good ground.

Step 12 * Remove any retaining rings or bolts that hold the fuel pump in the fuel tank.

Step 13 * Remove any electrical connections or fuel lines connected to the fuel pump. Replace the fuel pump.
o Tip: If equipped, inspect and replace strainer as needed.

Step 14 * Use reverse procedure to install fuel pump and assemble all components back to their original state.

Step 15 * Start the vehicle to verify repairs.


Good job (remember rated and comment this help).

Mar 03, 2010 | 1997 Nissan Pathfinder

1 Answer

Replaceing fuel pump


How to Replace a Fuel Pump
DIY & Save up to $219.24 (Complexity: Hard / Time: 3.2 hours)

Parts:
1. Fuel Pump - $140.07

Tools:
1. 3/8 in. Drive Ratchet - $7.55
2. Floor Jack - $145.54
3. Multimeter - $247.13
4. Jack Stand Set - $36.93
5. Flat Head Screwdriver - $3.14
6. Mallet Hammer - $6.83
7. Socket Set

Steps:
1 Locate the fuel pump.
- Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
2 Have a friend turn the key to the“ON” position while you listen for a high pitched hiss/whine coming from the electric fuel pump.
- Tip: If the fuel pump is located in the fuel tank, you can open the fuel cap and listen to hear the fuel pump. The fuel pump should run (priming the system with fuel) for a couple of seconds. Once it stops, you should be able to start the vehicle.
3 If the fuel pump does not make a sound (run and prime the fuel system) check to see if there is a fuse that supplies power to the fuel pump and check its location.
- Tip: Check the owner’s manual for location of the fuse box and fuel pump fuse.

4 Once you have found the location of the fuel pump fuse, remove the fuse from its housing and check to see if it is blown.
- Tip: A blown fuse will usually have a metal strip connecting both tabs that“blows out” (the wire looks as if it has been chopped in half or broken).

5 If you noticed that the fuse was blown, replace the fuse with a new fuse of the same amperage and repeat step 2.
6 If the fuel pump now works, you do not need to replace it. However, you will need to find what caused the fuel pump fuse to blow. We strongly recommend that this is done through a certified shop, unless you have the tools and knowledge to test electrical systems and diagnose more in depth problems.
7 If the fuse wasn’t blown, it should be checked for power and ground at the fuel pump. If there is power and ground present then you will need to replace the fuel pump.
- Tip: On most vehicles you may need to lower the fuel tank to access the power and ground leads for the fuel pump.

8 Siphon or drain as much fuel as possible from the fuel tank. Disconnect any possible fuel lines from the fuel tank.
9 Remove any retaining straps or bolts holding the fuel tank to the frame.
- Tip: You may be able to access the fuel pump from the bottom of the back seat or the trunk of the vehicle.

10 Using a digital multi meter, turn the key to the“ON” position and check for power at the fuel pump. Touch the negative lead from the DMM to a good ground and the positive lead of the DMM to the power cable at the fuel pump. You should have a reading that is equal to battery power. If you do not have a reading at all, you will need to inspect the power side of the fuel pump.
- Tip: With the ground lead of the DMM still connected to a good ground, touch the power lead to the positive side of the battery, to each side of the fuse, and again to the fuel pump. Wherever you notice the voltage reading goes from battery voltage to 0 you will need to replace whatever wires and fuse are in between.

11 If you have noticed that the power and ground being supplied to the fuel pump are both good, then you will need to replace the fuel pump.
- Tip: To check for a good ground, place the negative lead from the DMM to the ground side of the fuel pump, and the positive lead of the DMM to the positive side of the battery. If the reading on the DMM is battery voltage then you have a good ground.

12 Remove any retaining rings or bolts that hold the fuel pump in the fuel tank.
13 Remove any electrical connections or fuel lines connected to the fuel pump. Replace the fuel pump.
- Tip: If equipped, inspect and replace strainer as needed.

14 Use reverse procedure to install fuel pump and assemble all components back to their original state.
15 Start the vehicle to verify repairs.

Hope helps with this (remember rated this help) Good luck.

Feb 09, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

Fuel pump is not getting power, pump is brand new, not sure what fuses, or where the ground is located.


Hi....
Fuel PUMP fuse and relay is located in the Engine compartment
Fused block . Driver side. under the hood.
The Fuel pump relay Is labeled F/Pump.
And the Fuel Pump Fuse is labeled ECMB ( 20 amp.)
The ground for the fuel pump is located At left rear Frame rail.
Some times the Fuel pump harnes connector burn with the old pump.
Check the connector....

OK.. I hope this help on your question.
Thank you for use fixya..

Feb 03, 2010 | 2003 Chevrolet S-10

1 Answer

Turns over, doesn't fire. No gradual problem, just didn't start this morning. No fuel to fuel filter, wondered where the fuel pump relay is, is there a fuel pump fuse, and where is the ground wire f


Yes it has a fuel pump relay. It's located somewhere in your Main Fuse box.It can be found under the hood near the Fiewall or the front end of the vehicle.

May 31, 2009 | 2002 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...