Question about 1999 Ford Windstar

1 Answer

Heater will not switch to hot on our 1999 ford windstar it just clicks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

SOUND LIKE PROBLEM IN THE AC + HTR CONTROL SWITCH.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My windstar is a 99 it has no heat and you can hear a clicking sound under the center console. any ideas.


Temp . blend door actuator . The clicking is the stripped plastic gears in side the actuator . The actuator is a electric motor that controls the temp. blend door . Could be a video on youtube on replacing it .

Nov 20, 2016 | 1999 Ford Windstar

1 Answer

...i am looking for a diagram for a 1999 3.0L ford windstar engine to locate the heater hoses


There is a small radiator which forms the heat two hose will be running to that inside of car trace them back to engine normaly one from top of engine neqr thermostat half inch hose

Nov 13, 2015 | 1999 Ford Windstar

2 Answers

My 1999 Ford Windstar, the heater is Not blowing Hot air, the Fan is working. Where is the Thermostat located??


the thermostat is in the thermostat housing. that is the end part of the upper radiator hose, where it connects to the engine. assuming the car is otherwise running OK it is not your problem, replacing it is a waste of your time. most likely the heater core is shot, that is where you should be looking. it sits within the heater box which is most likely behind the dash under the glove box, over the passenger footwell.

Nov 18, 2010 | 1999 Ford Windstar

1 Answer

The heater only blows hot air sometimes


it sounds like a bad blend door motor.these are controlled electrically and not with a cable like older vehicles did.

Oct 27, 2009 | 1999 Ford Windstar

1 Answer

Heater vent won't switch from cold to hot. the heater core hoses are both hot and there is a dull thumping noise under the dash like a vacume switch is jammed


probably something feel down the defroster vent, have a helper check the vacuum motors as you switch from heat to cold, that should tell you wich one is jammed

Oct 26, 2009 | 1999 Ford Windstar

1 Answer

Just need to open door in heater box to get hot


it sound asd if its stuck give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local ford dealership and in the parts department they be able to get you picture and diagram showing you how to repair it if all fails stop by your local library and get your hands on a Haynes auto repair Manual for you van wish you the best of luck Michigan Man.

Oct 22, 2009 | 1999 Ford Windstar

1 Answer

Ford Windstar SE, 3.8L V6, 1999, front seat heat/defrost is cold


the blendor actuators strip out the gear inside the actuator cases on these all the time. replace the actuator.

Mar 10, 2009 | 1997 Ford Windstar

5 Answers

1999 Ford Windstar 3.8 no heat


If you have a knock or clicking noise behind the radio, it is the blend motor. The blend door is spring loaded and the gears in the blend motor are "stripped". The door is spring loaded so that the door is closed to the heater core. About 2 hours to replace and a lot of bending and stretching. You don't have to remove the dash, but all of the trim, radio, and controls will need to come out.

Nov 12, 2008 | 1999 Ford Windstar

1 Answer

Heater core


There is a small, white, control motor with a square plastic case that controls the blend damper. The motor always fails with the damper on the cold side. It is mounted on the front of the heater box directly behind the center stack (radio, heater controls) and is easily replaced by removing wiring plug and three mounting screws. Motor is about $60 from dealer.

Oct 30, 2008 | 1999 Ford Windstar

Not finding what you are looking for?
1999 Ford Windstar Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...