Question about 1997 Mercury Grand Marquis

2 Answers

How to replace a 1997 Grand Marquis window regulator. I took off the inside panel and was surprised to find the window regulator in blind spot within the door. Where do I go from here

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If it's the same as my 94 I think the answer your looking for is drill out the rivets (replace them with bolts). First remove the glass (also riveted in). The regulator ( without motor attached) comes out of the glass opening in the top of the door. Getting the interior door panel back on was the hardest part.

Posted on Oct 05, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 521 Answers

Local autoparts store to get a haynes manual or at minimum a repair diagram. Autozone usually has them in step by step format.

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fuse box on 1997 mercury marquis


All windows are on the same fuse in your vehicle.
If one window is not working, it is either a switch problem, a motor problem, or a regulator problem.
You will need to remove the door panel and see if the motor is getting voltage when the switch is actuated. If there is voltage at the motor connector when the switch is actuated, check to make sure that the regulator mechanism hasn't seized due to lack of lubrication (they are supposed to be lubricated annually but nobody remembers to do it.... then they seize).
If you can HEAR the motor turning but it is not moving the window, the plastic gear in the motor assembly has broken off. Chances are you will need to replace the window motor.

Jul 29, 2014 | 1997 Mercury Grand Marquis

Tip

How To Install Replace Power Window Regulator Crown Victoria Grand Marquis 92-11...


How To Install Replace Power Window Regulator Crown Victoria Grand Marquis 92-11 1AAuto.com

on May 22, 2012 | 1998 Mercury Grand Marquis

1 Answer

Motor works window does not go up drivers side 1997 grand marquis


u most likely have a bad gear pak in ur window motor,which can b serviced seperatly, or u have a window regulator that consists of plastic pulleys an steel cables monted on stamped steel frames,which are weak designs an almost always fails causing condition u decribed. if u remove dr panel u can see a bad regulator by noticing cables jus layn around not hooked to anything,or cables not routed thru the small plastic pulleys.if all ur cables are intact the gear pak which consists or plastic parts for safety reasons,has gone bad an can b serviced without buyng a new mtr, jus purchase the gear pak install an ull b bak in business. good luck

Mar 24, 2011 | 1997 Mercury Grand Marquis

1 Answer

Replacing power window cables


The cables are in a complete asmbley, called window regulator, you will need to replace the door panel, then support the glass, remove the two bolts to slide glass of the regulator arms and lock glass all the way up then unbolt regulator and remove. this is not hard to do i enclosed a diagram of the regulator and the bolt locations and the glass mount location on regulator, to remove the door panel ther are screws holding it in some places and then the panel must be pryed off, it uses plastic retainer that pop out of door and pop back in when panel is installed, there may be some hidden bolts so take your time removing it, hope this helps.note some of these cars use revits to hold regulator on, if thats the case drill them out and use small bolts and nuts to reinstall it.johnjohn2_71.jpg

Feb 26, 2011 | 1997 Mercury Grand Marquis

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

How do you change window regulator with window motor on a mercury grand marquis 98


You have to remove door trim panel for access. I can load steps on Monday, but go to ebay and type in grand marquis window regulator in ebay motors and look at pictures of regulators for sale to see what they look like.

Are you sure you just don't need motor? There are 3 dimples in inner door panel to drill 3/8" holes to remove motor bolts.

Dec 11, 2010 | 1998 Mercury Grand Marquis

1 Answer

Need instruction on removing 2003 Mercury Grand Marquis Rear Door panels.


www.autoclinix.com this site will help. should be just three screws. I have a mint 94 merc grand marquis LS and replaced both window regulators.

Jun 14, 2010 | 2003 Mercury Grand Marquis

1 Answer

How to replace passenger side outside mirror on a 1997 Mercury Grand Marquis?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. You can then remove the bolts securing the mirror onto the door

Sep 18, 2009 | 1997 Mercury Grand Marquis

2 Answers

I have a 1992 Mercury Grand Marquis. The rear passenger window will not go up or down. You can hear the motor running but the window won't move. The window is not off of the track. The regulator is not...


this happened with my car too!!! just hit the inside door panel hard and it should work again!!! email me for anymore questions
dubcars101@yahoo.com

Aug 25, 2009 | Mercury Marquis Cars & Trucks

Not finding what you are looking for?
1997 Mercury Grand Marquis Logo

685 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5522 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...