Question about 2006 Toyota Tundra

2 Answers

Maintenance Lamp How do I turn off Maintenance Lamp after Servicing it myself.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,077 Answers

Here's how you reset your maintenance light.

To reset the light,
Turn the ignition on
Make sure the odometer displays "ODO"
1.Turn the key off
2.Press and hold down the same button you use to get to "ODO"
3.Turn the key back to ON ( while still holding down the button)
4.Hold the button in until all the flashing lines on the odometer go away and the bunch of "000000" shows up and the maint reset light will turn off.
Your'e done.

If this doesn't work, you would have to try it on "trip A" instead of "ODO".

Posted on Oct 03, 2009

Testimonial: "Excellent Response"

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Turn key ON, push on trip reset knob until odometer (odo) milage reading appears, not trip A or B. Turn key off then push in and hold trip reset while turning key on. Continue holding trip reset depressed until the maint light ( will show dashes -------)stops flashing and then release the reset knob. Light should now be out. If at first it dont succeed read the instructions closely and try again.

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the maintenance light after servicing in Rav 4 (2006) model


turn engine off , push in trip zeroing button and hols it in while turning key . have to hold several seconds.at times

Feb 21, 2015 | 2006 Toyota RAV4

1 Answer

I have a 2003 206. Just recently a warning light with an audible signal has appeared. Also a spanner with 6150 code when I turn the key. Could you tell me what this is please?


You don't say what colour the light is but any light with a buzzer means you have to take action immediately!
The lamp with a spanner is the maintenance period light, means its due servicing.
Both of these can be sorted by a local dealer or specialist.
Don't delay.

Nov 05, 2013 | Cars & Trucks

1 Answer

My Tucson is out of the maintenance plan and i am doing the maintenace myself, where is the fuel filter situated and how do you get to it? They say in the fuel tank, but there must be an easy way to get to...


The filter is part of the fuel pump. You will have to drain the fuel tank and drop it down to access the fuel pump. This is a major undertaking, and very risky because of the gasoline. Unless you are having fuel starvation problems related to the fuel filter, I would not recommend servicing the filter until it is absolutely necessary.

Feb 22, 2011 | 2007 Hyundai Tucson Limited

1 Answer

How to remove the tail light on a 1999 dodge dakota


To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Screws from tail lamp
    • Lamp by pulling towards the rear to disengage retaining studs
    • Sockets from tail lamp
    • Bulb from socket
    • Tail lamp from cargo box
To Install:
  1. Install or connect the following:
    • Bulb in socket
    • Socket in tail lamp
    • Tail lamp in cargo box to engage retaining studs
    • Tail lamp screws
    • Negative battery cable

tecnovative_86.gif

Feb 04, 2011 | 1999 Dodge Dakota

2 Answers

I want to change the amber side marker light on a 2005 Mercury Mariner but the manuel says to take it to a dealer to have it done. Is it that hard to do myself? Thanks


Side Lamp/Front Turn Signal Lamp Bulb

Removal and Installation
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.

  1. Remove the 2 fender splash shield bolts.
  1. Remove the 3 fender splash shield pin-type retainers.
  1. Remove the screw and position the fender splash shield aside.
  1. Remove the front turn lamp bulb holder from the lamp assembly.
    a0014324.jpg
  1. Remove the front turn lamp bulb.
  1. To install, reverse the removal procedure.

snorkelbobby_1.jpg

Dec 07, 2010 | 2005 Mercury Mariner

1 Answer

Alarm servicing message comes on. How do I reset it myself?


Press and hold in the button to reset the mileage trip, then turn on the ignition, after 30 secs it will flash then disappear.

Jan 05, 2010 | 2001 Volvo S80

1 Answer

How do i replace the brake light on my 1997 ford taurus?


To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the luggage compartment quarter trim panels.
  3. Disconnect the rear lamp assembly electrical connector.
  4. Remove the lamp assembly mounting nuts.
  5. Pull the lamp assembly away from the body.
  6. Disconnect the rear lamp assembly bulb connectors.
  7. Remove the rear lamp assembly.

Mar 29, 2009 | 1997 Ford Taurus

2 Answers

Need to check turn signal contacts in column,


Best thing to do, honestly, is to purchase a chilton's or haynes manual when you are working around the air bags. Better safe than sorry.

Mar 14, 2009 | 1992 Buick LeSabre

1 Answer

Brake Light


hi from uk to change the brake light bulb/s on the getz is easy just open rear hatch then you will see 3x pozi drive screws alongside each lamp assy that screw /secure the lamp to body at the lower endof drain channel? remove screws and lift away lamp from body each bulb is accessable then now would be a good opportunity to clean the area at rear of lamp ? then reassemble is reverse as above my wife has one of these cars and has been absalutely trouble free for past 5yrs but it does get lots of tlc/servicing by myself hope the instructions are ok to follow?

Nov 23, 2008 | Hyundai Motor 2003 Elantra

2 Answers

Maintenance light turn orange. I bought the car 2 months ago. It was green when I buy it. After travelling for about 900 km it turns to orange. I don't have the manual. I dont know what it means. What...


hi there
When the car is near 12,000km since the last service,the indicator will turn yellow,if it exeeds 12,000km it will turn red.
To clear it switch the ignition on.
Reset service indicator by inserting key or another similar object of the same size into the slot below the indicator.
The service lamp will cancel the indicator for the next 12,000km.
I hope this helps you.

Jul 30, 2008 | 1991 Honda Accord

Not finding what you are looking for?
2006 Toyota Tundra Logo

347 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...