Question about 2006 Renault R18

1 Answer

How do you press the rear bushes in to place on a laguna suspension 04 year dci 2.2

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

With great difficulty i am affraid you need to optain a specil tool to do this and it is not cheap!! my advise is take it to a garage or get friendly with a renault mechanic

Posted on Oct 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Renault Laguna dci fuel cut off


The fuel cut off switch activates during a hard crash and on my Laguna it is located under the bonnet and is bolted to the passenger side suspension strut mounting near the top, hope this helps.

Feb 20, 2016 | Renault Cars & Trucks

1 Answer

I have a NISSAN CIFERO V6 3LTR 1994, I NEED A REAR RUBBER BUSHING THAT IS NEAR THE RIGHT HAND REAR WHEEL I WAS TOLD YOU CAN BUY ONE INSTEAD OF THE WHOLE ASSEMBLY, I WANT TO KNOW HOW MUCH AND WHERE TO BUY...


most suspension bushes are available from suspension repair shops. As you will need a press to do the job ,it is generally quicker and cheaper to have the shop do the job. With suspensions be aware that if one bush is failing then the others will not be far behind. Discuss this with an accredited suspension repair shop

Nov 13, 2014 | Cars & Trucks

1 Answer

Rear suspension,bushings,2005 jeep liberty


Generally the bushings aren't too expensive (likely about 25-30 each...But, unless you have done this kind of work, driving the bushings out and installing them can be difficult without a press. I've done many in-shop and its nothing like the ones I've done at remote locations using a hammer and chisels etc. You can do this yourself but I'd opt to do the r&r at home and have a machine shop do the actual bushing pressing. If you damage the arm ends you will need to replace the arm or do a bunch of bending to get the bushings back in place.
If you do have a press, than go at it!!

Aug 02, 2009 | 2005 Jeep Liberty

1 Answer

I need to know how to get to the rear suspension (tower)


i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal
  1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.
  1. Remove rear stabilizer bar as outlined.
  1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .
  1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .
  1. Lower the hoist and axle housing until the rear springs are released.
  1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
    -----------------------------------------------------------------
Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.
  1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
  2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
  3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.
Installation
  1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.
  1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).
  1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).
  1. Lower vehicle.
-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .
  1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.
  1. Remove rear stabilizer bar as outlined.
  1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .
  1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.
  1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .
  1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.
  1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .
-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
  1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
  2. Support the rear axle assembly .
  3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
  4. Unsnap parking brake rear cable and conduit from upper arm retainer.
  5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
  6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
  7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.
------------------------------------------------
Stabilizer Bar
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal
  1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .
  1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.
  1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .

Mar 05, 2009 | 1994 Lincoln Town Car

1 Answer

Noise from rear


This might be your muffler or something loose with the rear differential. What type of noise is it? metallic? Check your spare tire where it sits. Could be something loose around that, like a bolt or a screw jumping around on the bumps.
LEt me know if this helps.


Jan 24, 2009 | 2000 Renault 181

1 Answer

Laguna estate 03 plate


that souds like back axle bushings. regular problem on laguna 2. back axle ha to be removed and replace both sides. not very expensive

Jul 12, 2008 | 2000 Renault 181

1 Answer

Hyundai Excel Rear Supension 99-2000 model


SUSPENSION REASSEMBLY
1. Apply the specified grease to the inside of the left suspension.
2. Using special tools (09555-21100, 09555-21000), drive bushings, into the suspension arm.

CAUTION
1) Apply grease to all outside surfaces of bushings.
2) Drive bushing in until the notch on the special tool
(09555-21000) reaches the end of the suspension arm.
3. When replacing the dust cover, insert a new one up to the center position (stopper) of the right suspension arm.
4. After applying grease to the surface of the right suspension arm, install the rubber stopper.
5. Slowly push the right and left suspension arms together. Wipe away the surplus grease. Align the marks on the stabilizer bar and the stabilizer bar bracket.
6. Install the rubber bushings, fixtures and washers.
7. After aligning the fixtures with the suspension arms according to the alignment marks, loosely tighten the nuts.

CAUTION
1) Install the washers and fixtures in the correct direction
and position as shown.
2) Tighten the nut to specification with the vehicle lowered
to the floor.

8. Pack grease in the dust cover and lips, and secure the dust cover with the clamp.

Jun 21, 2008 | 1994 Hyundai Excel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

xxxxxx xxx

Level 3 Expert

4860 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...