Question about 1991 Honda Accord

1 Answer

I can not get the spark plug wires back onto the plug

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 5,763 Answers

You just slide them back on with a little preasure.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do my spark plug wires I'm my 1994 ford


Probably not seated well on the plug. When you push the plug wire boot over the plug, you have to make sure the wire end terminal's ring end snaps onto the spark plug. It is not connected tight until you hear the wire's end terminal snap or click onto the tip of the spark plug. If you can't hear the snap, the end of the wire may not be seating onto the spark plug tip. Push the boot back away from the spark plug wire end to investigate-the boots can get very stubborn with age-keep twisting it and pushing it till you get it moving back from end of wire. Examine the metal end tip of wire-trey to snap a spark plug down onto it now-if there is a problem with the end terminals you will see it-it may be too big to snap over the spark plug tip and hold securely, or if the ends are bent, use pliers to straighten them out. If these are aftermarket spark plug wires, the end terminals may be too small to go over the spark plug tip. You would then need a new set of spark plug wires.

I suspect you just have not pushed the wires down far enough to seat them on the plugs-push the wires onto the plugs until you hear them snap or click. Then they are seated firmly, and should not be popping off.

Sep 04, 2013 | Cars & Trucks

1 Answer

I want to change my own spark plug's


Instructions
    • Locate the spark plug cables along the top or the sides of the engine, depending on CR-V model. Once the engine cools, use the trim panel tool to twist the spark plug wire at the wire's boot, which is the larger rubber portion located on top of the spark plug.
    • 2Pull back on the spark plug wire to remove it from the spark plug.

    • Place the socket on top of the spark plug and turn it counter-clockwise to unscrew and remove the spark plug from the well.
    • 4Rub anti-seize lubricant onto the new spark plug threads and on the tip of the spark plug.
    • 5Insert the new spark plug into the well. Manually turn the plug clockwise to thread the spark plug into place.
    • 6Test the tension on the plug with the tension testing tool. Adjust the tension as needed. Honda CR-V spark plugs generally need a tension between 10 and 15 foot pounds. The spark plug's packaging indicates its suggested tension.
    • 7Replace the spark plug wire, turn it from side to side and lock it into place. Continue the process with the rest of the spark plugs one at a time until all of the spark plugs are replaced.

Jun 24, 2012 | 1999 Honda CR-V

1 Answer

Can't pull spark plug wires off of the spark plugs


sometimes they can get stuck on prety good if they have been on for a while. Try twisting them like you either screwing or unscrewing the spark plug. You will feel it brake loose and then you will be able to remove it.

To help prevent it from happening in the future put a little di-electric grease in the spark plug wire boot before you install the wire back onto the plug. The d-electric grease will keep the boot from sticking to the spark plug.

Nov 07, 2010 | 2004 Pontiac Grand Am

1 Answer

How do I change the spark plug of the dodge magnum 2006


· Open the hood and remove the bolts that hold the engine cover in place, if your Dodge comes with an engine cover (depending on model and year). If so equipped, pull the cover off the engine.

· 2

Grab a spark plug wire by the base of the wire and pull the wire up and out of the engine. (You may need to wiggle it back and forth while pulling up on it to get it out of the engine.)

· 3

Trace the wire back to the power distributor and pull the spark plug wire off the distributor. Make a note of the plug orientation.

· 4

Install the new plug wire in the place of the removed one. Match the new wire with the old one to make sure they have the same size. Press the plug wire over the distributor electrode and onto the spark plug firmly, so that the ends are secure. Installation is the reverse of removal procedure.

· 5

Repeat the above procedure for all the other spark plug wires. It is best to change all the spark plug wires at the same time.

Sep 29, 2010 | Dodge Magnum Cars & Trucks

1 Answer

Where are the spark plugs located at


I found this solution and will not take credit for it, I had the same problem. To change the spark plugs on a 2000 Kia Sephia, at least in a 1.8L version, first disconnect the battery, then, remove the black plastic cover on top of the motor. There should be 6 Phillips-head screws holding it down. After removing the plastic cover, you will see two rubber covers for the spark plug wires on each side, and two gel-looking insuated tubs attatched to more wires in the middle. To remove two of the spark plugs, you must carefully pull the rubber covers upward. They clip onto the spark plugs so you will need to use careful force to pull them out. Once you have them pulled out, you can look in and see the plug. It requires a 5/8 spark plug socket with an adapter to reach in. Make sure you push the socket on hard enough so that it clips onto the spark plug, other wise it will fall over and you wont be able to get it out without a LOT more work. Finish that plug by plugging the rubber covered spark plug wire back onto the spark plug, covering the hole. You can do the same thing for the plug on the opposite side. For the two in the middle, you need to first unbolt and remove the insulated boxes that cover the spark plug holes (you can unplug the white connectors but make sure you plug them back in when you are done). Then all you have to do is do the same thing you did with the two outer ones to replace the plugs. Perform this one plug at a time, and make sure you cover the holes with a cloth or paper towel if you leave them open for any period of time. When you finish, make sure all the wires are connected, then reconnect the battery.

Sep 15, 2010 | 1999 Kia Sephia

1 Answer

How to change spark plugs in 2002 ford f150 with a 5.4ltr


Hello my name is Israel and I will be glad to help you. On this vehicle it is fairly easy. This vehicle has a coil to plug assembly, meaning that each spark plug has its own coil. All you have to do is carefully pull the spark plug wire off the spark plug with a little "tough love". Using a 5/8 socket remove spark plug and replace with new one, connect spark plug wire until you feel it "snap" back onto the spark plug. Repeat with the other 7 spark plugs. Good Luck.

Jun 28, 2010 | 2002 Ford F150 Regular Cab

1 Answer

What spark pulg wire go in order on 6 cly onto spark plug --what is the back 3 plugs in order and front 3 plugs in order


the firing order should be - 1-6-5-4-3-2 , Front Bank 1-3-5, Rear Bank 2-4-6. Hope this helps.

carsandcomps,

Guru, Premium Expert @ Fixya.com

TIP: When replacing spark plugs and wires, do one at a time to ensure each is placed back in it's original position and place.

Jun 14, 2010 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Replacing spark plugs


Not exactly sure what you need?
Standard Rules:
Use a Spark Plug Socket to remove and install Spark Plugs.
Replace (remove) one Wire at a time from one Spark Plug.
Replace One Spark Plug at a time. Use Anti-Seize Grease applied moderately to the threads on the new Spark Plug.
Using a Socket (with a extension) START all installations using your hands. This prevents cross-threading and stripping of the threads inside the Heads.
Standard Torque 15-20 ft-lbs.
Replace the One Wire connection to that One Spark Plug.
Replace that One Wire connection to the Ignition Coil.
Go onto the next Spark Plug using the above Rules.
Repeat.

For the 3.4L V6:
Firing Order:
1-2-3-4-5-6
Cylinders:
......(back)
1.......3.......5
2.......4.......6
......(front)
Ignition Coil Connections:
............(back)
.|.5..2.|..|.3..6.|..|.4..1.|
............(front)

Mar 21, 2010 | 1997 Chevrolet Venture

1 Answer

Spark plugs


Wait until the engine is cold. Carefully remove the spark plug wires from each cylinder. Pull the wires by the boot and not by the wire or the wire will be ruined. Now, using a spark plug socket (one that has a rubber fitting inside of it) and an extension remove the spark plugs by turning the wrench counterclockwise. Insert the new plug into the socket so that the rubber will hold the plug in. Place the plug and socket down inside of the hole. Hand tight the plug by turning the extension clockwise. Once the plug cannot be turned by hand, tighten it a little more with the socket wrench. Install the wires back onto the plugs by pushing down on the boot. thanks for using fixya and plsase do rate the solution.

Jun 12, 2009 | 1993 Saturn SC2

1 Answer

Were are the spark plugs


Hello, Make sure you use AC Delco plugs 41-950 and wires, these cars are very sensitive to this brand, you will see 4 wires going to 4 round rubber plugs in the front of your motor and you can follow the 4 wires at the back of the motor, pull this round plug its about 5-6 inches long, looks like a cows utter, the spark plug is at the bottom of that hole, you will need a long rachet extention with a 5/8 spark plug remover, its a longer rachet that usally comes will any set, you need to use the spark plug bit because it has a rubber piece in it to hold the spark plug on the way out, I use a regular bit when putting new plug back in so it does not stick down there...some people tape the bit onto the extention so you can pull it back out without the bit sticking down there...you dont have to wrench them in really hard, just snugg them up good.
I alway replace the spark plug Wires one by one even thou they are numbered...hope this helps.
Regards,
Joe.

Nov 01, 2008 | 1994 Cadillac DeVille

Not finding what you are looking for?
1991 Honda Accord Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...