Question about 1997 Nissan.5 Altima

1 Answer

How do I access the windshield wiper assembly?

How do I access the windshield wiper assembly to re-attach the wiper linkage on a 1997 Nissan Altima?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have to remove the wiper arms by prying off the black platic piece over the nut. Remove the nut and the wiper arms. There should be 5 places on the black plastic piece that runs the length of the windshield. Remove 4 of them by prying them out. The one is the middle is a screw. Pull away the plastic piece and you should have access to the mechanism below. I think you need to replace the linkage if it has fallen off.

Posted on Oct 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 nissan sentra windshield wiper center pivot arm resident glue


i use a brand called LOCKTITE but just google thread lock products and there are a few to choose from , and cheaper online

May 12, 2014 | 1997 Nissan Sentra

3 Answers

My windshield wipers wont work.


It Sounds Like, Either The Arms Are Loose ,If You Can Hear Something Moving Behind The Dash,
Or The Linkages Are Seized ,If The Motor Just Hums No Movement Heard,In Which Case Try Spraying Q 20 On The Linkage And Try Moving The Wiper Arms By Hand To Get It Going Again,
If Not The Motor May Just Be Burn;t Out.

Mar 16, 2013 | Cars & Trucks

1 Answer

The windshield wiper driver side does not move. Passenger side does. How do I get to it?


The wiper motor must be directly linked to the passenger side wiper, and the driver side wiper gets its action from the passenger motion. probably the linkage from passenger wiper to the driver side wiper must be the problem. Under the dashboard you can check it, the linkage must be snapped off. (safety first)

Sep 21, 2010 | 2000 Nissan Altima

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

Windshield wipers will not move. Arms from motor


Hello

The windshield wiper linkage comes as an assembly. The assembly comes with the two rotating splines that the wiper arms attach to. you must remove wiper arms. Remove cowl trim and remove bolts that hold the pivot points to the body. The new linkage that snaps to the wiper motor should come with a new retaining clip. You have to fish the linkage assembly through the access holes in the body by un bolting the wiper motor.

Dec 19, 2009 | 2002 Ford E350

1 Answer

Windshield wipers stopped working on 1998 Nissan Sentra. Is it a fuse problem? If so, where is fuse box and which fuse? Is it a motor problem? is this an easy diy fix?


Water can enter and displace the grease in the wiper arm linkage ball joint where the wiper linkage attaches to the wiper motor linkage.

This can result in gradual wear over a period of time inside the joint that could lead to the separation of the wiper linkage assembly from the wiper motor linkage at the ball joint. A loss of windshield wiper function can result when this separation occurs.

To prevent grease from being washed out of the joint, the dealers will modify by adding a water diversion seal that will prevent water from entering the windshield wiper linkage ball joint area.

Jun 13, 2009 | 1998 Nissan Sentra

1 Answer

Wiper Linkage


yes the wipers pull off and you need to get the linkage from the dealer the parts just snap on

Mar 10, 2009 | 1997 Nissan.5 Altima

1 Answer

1997 nissan altima


remove the arms and the panel or the neted are shich hides the motor and the linkage, what you will find is that the link would have come off either from the motor itself or from the wiper transmission it is linked with a small plastic like press on cup only available from a nissan dealer very cheap and you can do it with very little mechanic's skill

Dec 04, 2008 | 1997 Nissan.5 Altima

1 Answer

97 nissan sentra


check the linkage from the motor to the wiper arm. they are attached with plastic cups. go to nessan dealer and get set of new cup replace them.

Oct 10, 2008 | 1997 Nissan Sentra

1 Answer

1997 nissan altima


it could be the motor or the linkage between the the two motors. the motors are under the dash and you would be better off taking to a small shop to keep the cost at a minimum.

Aug 28, 2008 | 2001 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

852 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...