Question about 1996 Toyota Avalon

1 Answer

How can I disconnect the a/c compressor? - 1996 Toyota Avalon

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

If the compressor is cycling all the time like its low on freon then just unplug the electrical connector on the compressor itself. if its locked up, you would have to buy a drive belt for the same car that didnt have ac if toyota made and avalon that didnt. and possibly remove the compressor if its in the way

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have to replace my alternator on my 2006 H3. I can unbolt it but I just read a post that says I have to take the fender off. Is that true?


Inner fender well ! But that's not the worst part , The A/C compressor has to come out to get the alternator out .
Removal Procedure
Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
Remove the drive belt. Refer to Drive Belt Replacement for the 3.5L (L52) engine.
Raise and support the vehicle only high enough to access the air conditioning (A/C) compressor through the wheelhouse. Refer to Lifting and Jacking the Vehicle .
Remove the left front wheel. Refer to Tire and Wheel Removal and Installation .
Remove the left wheelhouse liner. Refer to Wheelhouse Panel Replacement .

Disengage the A/C compressor electrical connector from the bracket.
Recover the A/C system. Refer to Refrigerant Recovery and Recharging .
Disconnect the A/C condenser and evaporator lines from the compressor.
Remove the A/C compressor mounting bolts (2, 3) ONLY.
The upper mounting bolt (2) will remain with the A/C compressor (1).
Lower the vehicle.

Reposition the protective boot from the generator output BAT terminal.
Remove the generator output BAT terminal nut (2) and remove the generator lead (1) from the generator.
Disconnect the generator electrical connector.

Remove the 3 generator bolts.
Position the A/C compressor forward, in order to gain clearance to remove the generator.
Remove the generator.

May 22, 2017 | Cars & Trucks

1 Answer

Why does the ac comp fuse onder hood keep blowing


Possible direct short in compressor clutch. Disconnect wiring harness from compressor and then turn AC on> If fuse doesn't blow, then problem is in compressor/clutch. Suspect it to be seized. If fuse blows while compressor disconnected then problem in wiring.

May 09, 2015 | 2004 Kia Optima

1 Answer

My compressor smels like its berning


Clutch is bad or compressor is leaking and the oil has dried out...At that point it is probably fried. disconnect the electrical lead to the compressor to it to prevent further damage and possible seizure and ripping of belt. and take it to a mechanic. I assume you are talking about the air conditioning compressor. Just keep in mind you probably won't be able to defog you windows once you disconnect the compressor .

Mar 10, 2015 | Cars & Trucks

1 Answer

How to disconnect air compressor on dodge 2003 caravan?


You get a belt for that engine without A/C . It will be shorter and you can't leave the compressor on the engine. So keeping dirt out of the hoses is most important.

Jun 25, 2014 | 2003 Dodge Caravan

1 Answer

How to take out air condition compreser out of a2001 mercury sable


have dealership discharge airconditioning system.you need to disconnect refrigerant lines going to the AC compressor you probably need refrigerant lines disconnect tools to remove disconnect refrigerant lines.you need to remove drive belt.and safely raise support vechicle remove tire or wheel work from under vechicle you have to loosen AC COMPRESSOR bolts then remove AC COMPRESSOR.be sure pour old refrigerant in a measuring cup so you can pour same amount new oil in the new compressor.add couple ounces if old AC COMPRESSOR dry.

Feb 11, 2013 | 2001 Ford Taurus

1 Answer

I have a 96 windstar and when i turn the heat on the a/c compressor starts up. how can i disconnect the compressor or fix the problem?


In some heat settings the A/C compressor will run to remove moisture from the cabin. There is a connector on the a/c compressor if you want to disconnect it.

Nov 13, 2012 | 1998 Ford Windstar

2 Answers

I need a Diagram on the Serpentine belt for an 2002 Eclipse. I need to know how to bypass the AC compressor.


The compressor cannot be by-passed, but you can disconnect the compressor clutch by disconnecting the two wire connector at the compressor; then the compressor pulley is just an idler.

Jul 30, 2011 | 2000 Mitsubishi Eclipse

1 Answer

How to install a 1999 yukon ac compressor


Hi.

Follow below...

jshreader_20.jpg

REMOVAL PROCEDURE

CAUTION: Refer to Battery Disconnect Caution in Cautions and Notices.

1. Disconnect the negative battery cable.
2. Recover the refrigerant.
3. Remove the drive belt.
4. Disconnect the refrigerant hose assembly from the compressor.
5. Cap or plug all of the open connections.
6. Disconnect the electrical connectors, as necessary.
7. Remove the bolts.
8. Remove the compressor from the bracket.
9. Drain the compressor oil.
10. Measure the compressor oil. Refer to Adding Oil .

INSTALLATION PROCEDURE

1. Fill the compressor with oil. Refer to Adding Oil .
2. Install the compressor to the bracket.

NOTE : Refer to Fastener Notice in Cautions and Notices.

3. Install the compressor mounting bolts.

Tighten
Tighten the bolts to 50 N.m (37 lb ft) .

4. Connect the electrical connectors, as necessary.
5. Install the refrigerant hose assembly to the compressor.
6. Install the drive belt.
7. Connect the negative battery cable.
8. Charge the system. Refer to Refrigerant Recovery and Recycling, Adding Oil, Evacuating and Recharging Procedures .
9. Inspect the system for leaks.

I hope this helps.

Thanks...

Dec 03, 2010 | 1999 GMC Yukon

1 Answer

How do i remove the ac condenser on a mazda 3


B3E071161450W02
1. Disconnect the negative battery cable.
2. Discharge the refrigerant. (See REFRIGERANT CHARGING.)
3. Remove the splash shield.
4. Remove the A/C drive belt. (See DRIVE BELT REPLACEMENT [LF].)
5. Detach the two wiring harness clamps.
6. Disconnect the magnetic clutch connector.
7. Remove the A/C compressor protector.
8. Disconnect the cooler hose (LO) and cooler hose (HI). Do not allow remaining compressor oil in the refrigerant line to spill. (See Refrigerant Line Removal Note.) (See Refrigerant Line Installation Note.)
Caution • If moisture or foreign material enters the refrigeration cycle, cooling ability will be lowered and abnormal noise or other malfunction could occur. Always plug open fittings immediately after removing any refrigeration cycle parts. 9. Remove the compressor protector.
10. Remove in the order indicated in the table. Do not allow remaining compressor oil in the A/C compressor to spill.
Caution • If moisture or foreign material enters the refrigeration cycle, cooling ability will be lowered and abnormal noise or other malfunction could occur. Always plug open fittings immediately after removing any refrigeration cycle parts.
b3e0711w427.png

11. Install in the reverse order of removal.
12. Perform the refrigerant system performance test. (See REFRIGERANT SYSTEM PERFORMANCE TEST.)
A/C Compressor Installation Note 1. When replacing the A/C compressor, remove the following amount of compressor oil from the new A/C compressor.
Amount drained (approx. quantity) • 155 ml {155 cc, 5.24 fl oz} - [compressor oil from old A/C compressor + 15 ml {15 cc, 0.5 fl oz}]

Aug 10, 2010 | 2007 Mazda 3

1 Answer

I need a how to install a air compressor on my VW 97 Jetta GLX


You'll need to disconnect the high and low pressure lines from the compressor. Unplug the electrical connector for the compressor. Remove the belt. Unbolt the compressor from the motor. Reinstall, connect a vacuum pump to the high side A/C fitting, start the vacuum pump, run pump until to have about 15psi of vacuum and then disconnect the pump and refill with refrigeraint.

Jul 25, 2009 | 1997 Volkswagen Jetta

Not finding what you are looking for?
1996 Toyota Avalon Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...