Question about 1994 Ford Crown Victoria

1 Answer

Need to replace power antenna is there any easy way to get old one out without removing door or fender?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 89 Answers

The power antenna motor comes out thru the fender well.you have to remove the tire and rim,and loosen or remove the fender well.if the mast is just broke,you can replace it if the plastic gear drive is not broken inside.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bolt that holds in my antenna has completely stripped of the threading. What is everyones advice should I get a new in dash sound system and antenna or just replace the bolt?


If you have an in fender antenna ( front fender) it should be accessible from inside the guard without removing the fender. You will have to remove the inner splash guard to get to it. Removing the wheel helps a lot to do the job The antenna is held in place in the fender by the silver nut at the base of the antenna just outside the fender.

Nov 05, 2014 | 2006 Jeep Liberty

1 Answer

Power antenna


I was able to remove the antenna on a 1986 cadillac
deville many years or decades ago & don't remember
even having to loosen any fender bolts
The solution is to install a new one IF Avail
I remember the only issue was the wiring
I cut the & spliced the new antenna to the old
harness as I had access issue in the body,not
the problem you have removing it
I think you get it out from the bottom,the most
you would do is loosen the bottom of the fender
not remove it

Jul 16, 2013 | Oldsmobile Cars & Trucks

2 Answers

Replace antenna


Hi John,here's a link on removing your power antenna.

Jun 06, 2013 | 2000 Nissan Pathfinder

1 Answer

Need to replace radio antenna on a 99 isuzu rodeo


I just replaced the antenna on our 02 rodeo. No need to remove radio or anything in dash. This is how I did it.
First you will need access to back of fender, enough room for your hand. Open hood and remove 3 bolts running along top of fender, open passenger door and remove top bolt holding fender. Gently pry top of fender away from vehicle. Place object in gap to hold fender ( I used the head of a rubber mallet). Reach inside fender and disconnect old antenna, follow cable through wall into passenger compartment. Gently pull cable from behind carpet and unplug old antenna from coupler. Connect new antenna to fender ( replacement antenna I ordered was slightly smaller than opening so I had to add washer). Run new antenna cable through wall and plug into coupler. Re-attach fender
1_7_2013_12_53_34_pm.jpg

Aug 23, 2012 | 1999 Isuzu Rodeo

2 Answers

Where is the power antenna motor located for a 1992 buick regal?


I have not owned a buick for years. However, the one I did have trouble with the power antenna motor was located directly under the antenna. It was in the rear fender housing. I have to remove the trunk lining on the side of the fender. It was mounted a bracket. It was easy to replace as it all comes as a complete assembly. Hope that helped

Feb 21, 2012 | 1992 Buick Regal

1 Answer

Antenna bolt broke, how to fix antenna base.


This is probably way more information than you need, but here goes. I just had the same problem with my dads 2001 YUKON and wanted to put the stock wire back. It was not easy, but it can be done.

Remove the glove box, and plastic side panel on the dash
As you are looking through the removed area, there is a silver computer there, remove the bracket and move this computer.
Behind the computer there will be the plug in for the antenna. One side goes to the radio, the other to the fender.
Unplug the cable, and tape/fasten a length of wire to it so that when you pull it out, you have a guide to get the new wire back through the firewall.
Remove the old ant. and then take the guide wire and fasten to the new cable. Pull this guide wire through while someone else is feeding from the fender area.
Replug it, and reinstall the computer and glove box door.

Also, be aware and make sure that the new cable with stud matches the ant. mast. GM changed the size of the stud (for unknown reasons)and you may need to get a new matching mast. I could not use my old one

Good luck!



Dec 01, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

My antenna on 1996 Thunderbird 2 door was broken off by some kids. It was a power antenna. I just want to listen to some music and stay cheap on the fix. Someone said I have to remove the fender over...


remove front right rear screws on splash shields. you should be able to remove it with out removing the fender. you can get one at the salvage yard.

Apr 11, 2009 | 1998 Volvo S70

1 Answer

91 Olds electric antenna does not work; noise continues after shu


The drive cable in your power antenna is broken. You should be able to unplug the motor or cut the ground wire. The motor is on the bottom of your antenna, under the fender.

Mar 30, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Remove power antenna - 96 Seville


If there is a slot in the "fender hole", it unscrews with a big screwdriver If not, check for a slide clip under fender where it goes through.

Jan 17, 2009 | 1996 Cadillac DeVille

1 Answer

Replacing radio power mast on 2002 toyota 4runner


Sometimes you can put the new antenna cord in the motor, even with the old piece in there, and not have a problem. But, if it makes noise, the fender well needs to be pulled back, and the antenna motor removed enough to pull the back plate off,and remove the rest of the plastic cord. I have done MANY MANY of these. Its easy, some plastic clips, 1 10mm bolt, and some phillips screws.

Jan 01, 2009 | 2002 Toyota 4Runner

Not finding what you are looking for?
1994 Ford Crown Victoria Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...